• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Effect of interfacial modification on the thermo-physical property of Diamond/Al composites fabricat

Effect of interfacial modification on the thermo-physical property of Diamond/Al composites fabricat

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：adfazzzzzzzzzzzzz
【摘 要】
：
　　In this paper, the molybdenum coating was successfully deposited on the surface of diamond particles by direct current magnetron sputtering method, its surf
【作 者】
：
GuoWeiqiang;ZhaoXun;XiongDegan;LiuMeng; 
【出 处】
：
第二届中国国际复合材料科技大会 (CCCM-2)
【发表日期】
：
2015年期
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　In this paper, the molybdenum coating was successfully deposited on the surface of diamond particles by direct current magnetron sputtering method, its surface morphology and chemical composition were analyzed.Then the Diamond/Al composites was prepared by gas pressure infiltration method, and the effects of the heat-treatment temperature on the thermal conductivity were studied in detail.
其他文献
Thermal Expansion Characteristic of CNTs/7075 Composites Prepared by Friction Stir Processing
　　7075 based composite reinforced with carbon nanotubes was prepared by friction stir processing.The thermal expansion coefficient of CNTs/7075 composite with
会议
Fabrication, welding and service evaluation of B4C/Al neutron absorbing material
　　Due to high boron content and low density, new B4C/Al neutron absorbing material is widely used for storage and transportation of spent fuel in place of B-c
会议
Effect of the content of carbon nanotubes on the mechanical properties of Aluminum Matrix Composites
　　Aluminum matrix composites reinforced by multi-walled carbon nanotubes (MWCNTs/Al) were fabricated by friction stir processing, and effect of content of MWC
会议
Modification of rare earth B4C reinforced copper-based electrical contact material: Properties and p
　　The high-performance copper-based electrical contact materials were prepared via B4C modified by rare earth salt as reinforced agent.The properties were obt
会议
Deformation coordination of 06Cr19Ni10/Q235 clad composite materials under uniaxial load at room tem
　　In the present work, 06Cr19Ni10/Q235 clad composite materials are selected as the target materials.Then the deformation behavior, the surface deformation an
会议
Hot deformation mechanism and constitutive modeling of SiCp/2009Al composites
　　The present work studied hot deformation mechanism of powder metallurgy processed 17%vol.SiCp/2009Al composite via hot compression tests.The processing map
会议
Fabrication and properties of Al-based hybrid composites reinforced with SiC micro-particles and SiC
　　Hybrid reinforced aluminum matrix composites were fabricated by powder metallurgy method, with a controllable volume fraction of micro-sized and nano-sized
会议
Thermal conductivity of SiCp/Al composite with different SiC particle size and volume fraction
　　In order to study the effects of SiCp size and volume fraction on thermal conductivity of SiCp reinforced aluminum matrix composites, SiCp/2024Al composites
会议
Influence of aging temperature on microstructure and mechanical properties of SiCp/Al-Si matrix comp
　　The mass fraction of 30% SiC particles reinforced Al-Si matrix composite was prepared by One-way press method, sintering and hot extrusion.The microstructur
会议
Microstructure and Wear of CNTs/Al composites prepared by rotational friction extrusion
　　The multi-walled carbon nanotubes (CNTs) reinforced Al matrix composites were prepared by Rotational friction extrusion (RFE), And to analyze the microstruc
会议