Deformation coordination of 06Cr19Ni10/Q235 clad composite materials under uniaxial load at room tem

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户：softzheng1

【摘要】

：

　　In the present work, 06Cr19Ni10/Q235 clad composite materials are selected as the target materials.Then the deformation behavior, the surface deformation an

【作者】

：

JIANGQmgwei;ZENGJunjie;JIANGYehua;

【机构】

：

Faculty of Materials Science and Engineering,Kunming University of Science and Technology,Kunming 65

【出处】

：

第二届中国国际复合材料科技大会 (CCCM-2)

【发表日期】

：

2015年期

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　In the present work, 06Cr19Ni10/Q235 clad composite materials are selected as the target materials.Then the deformation behavior, the surface deformation and damage characteristics of these samples were considerably examined at different conditions (e.g.stain rate, loading direction, cladding ratio, and so on).

其他文献

Effects of CeO2 on microstructure and mechanical properties of particulate reinforced aluminum matri

　　In order to study the effects of CeO2 on microstructure and mechanical properties of SiC particles reinforced aluminum matrix composites, the raw materials

会议

AlN particles reinforced Cu-base composites: preparation and properties ZHANG Yu,SONG Meihui*,LI Yan

　　In this work, AlN/Cu composites were prepared by means of powder metallurgy.The effect of AlN content and preparation process on the structure and propertie

会议

Preparation technology and properties of Al2O3/Fe matrix composite

　　Metal matrix composite is a impotant new engineering materials due to posing the characterization ceramics and the predomination of metals.Al2O3/Fe matrix c

会议

Preparation and wear behaviour of submicrometer B4Cp/2009Al composite

　　Submicrometer boron carbide particles with different volume fraction (2%~6%) reinforced Al matrix composites were prepared by multi-stage vacuum hot pressin

会议

Influence of Sintering Temperature on Properties of M2052 Alloy Prepared by Powder Metallurgy

　　Manganin alloy is a kind of twin type high damping alloy.Studies have reported the manganin alloy has good damping capacity and excellent mechanical propert

会议

Study on in-situ metallization of carbon fiber surface

　　The copper salts on carbon fibers(Cf) surface can be reduced to native copper in hydrogen gas atmosphere, while under the high-temperature environment.Compo

会议

Thermal Expansion Characteristic of CNTs/7075 Composites Prepared by Friction Stir Processing

　　7075 based composite reinforced with carbon nanotubes was prepared by friction stir processing.The thermal expansion coefficient of CNTs/7075 composite with

会议

Fabrication, welding and service evaluation of B4C/Al neutron absorbing material

　　Due to high boron content and low density, new B4C/Al neutron absorbing material is widely used for storage and transportation of spent fuel in place of B-c

会议

Effect of the content of carbon nanotubes on the mechanical properties of Aluminum Matrix Composites

　　Aluminum matrix composites reinforced by multi-walled carbon nanotubes (MWCNTs/Al) were fabricated by friction stir processing, and effect of content of MWC

会议

Modification of rare earth B4C reinforced copper-based electrical contact material: Properties and p

　　The high-performance copper-based electrical contact materials were prepared via B4C modified by rare earth salt as reinforced agent.The properties were obt

会议

Deformation coordination of 06Cr19Ni10/Q235 clad composite materials under uniaxial load at room tem

其他学术论文