【摘 要】
：
Microstructure evolution and properties of hot-extruded Inconel 625 alloy were investigated at different creep temperatures, aging time and strain rates. The experimental results indicate that the Inconel 625 alloy exhibits an excellent creep resistance a
【机 构】
：
State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals, Lanzhou University
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Microstructure evolution and properties of hot-extruded Inconel 625 alloy were investigated at different creep temperatures, aging time and strain rates. The experimental results indicate that the Inconel 625 alloy exhibits an excellent creep resistance at 700 ℃ and below. When the creep temperature rises to 750 ℃, the creep resistance falls drastically due to the failure of phase transformation strengthening and the precipitation of a large amount of δ phase and σ phase at the grain boundary. The special temperature-sensitive characteristics of Inconel 625 alloy play a very important role in its fracture. When the strain rate is 8.33×10-3 s-1, the strength of the specimen is higher than that of other parameters attributed to the effect of phase transformation strengthening. With the increase of Ni3 (Al, Ti), the phase transformation strengthening inhibits thickening of the stacking faults into twins and improves the overall mechanical properties of the alloy. With the increase of the aging time, the granular Cr-rich M23C6 carbides continue to precipitate at the grain boundary, which hinders the movement of the dislocations and obviously increases the strength of the samples. Especially, the yield strength increases several times.
其他文献
The Z-type ferrites of nominal composition Ba3Co2Fe24O41+x wt％ Bi2O3, where x=0.25, 0.5, 1.0, 1.5, 2.0, were prepared by conventional ceramic processes. The influence of Bi2O3 content on the bulk densities, microstructures, magnetic and dielectric propert
A novel fiber optic sensor based on optical composite oxygen-sensitive film was developed for determination of 2,4-dichlorophenol (DCP). The optical composite oxygen-sensitive film consists of tris(2,2\'-bipyridyl) dichloro ruthenium(II) hexahydrate (Ru
The microstructure and texture evolution of Fe-33Mn-3Si-3Ai twinning induced plasticity (TWIP) steel were studied by the scanning electron microscope (SEM) and X-ray diffraction (XRD) at room temperature.After quasi-static tensile,the texture evolution of
Different failure modes and morphologies were found in the chemical vapor infiltration (CVI) 2D C/SiC torque tubes with different thickness. To characterize the density and porosity of the ceramic matrix composite (CMC) torque tube, a CT test was conducte
A novel low temperature co-fired ceramic (LTCC) material was fabricated by zinc titanate (ZnTiO3) ceramics doped with B2O3-BaO-SiO2-ZnO-Li2O (BBSZL) glass. The influences of BBSZL glass on wetting behavior, sintering activation energy, phase composition,
Amine-functionalized imidazolium-based poly(ionic liquid) brushes on mesoporous silica were synthesized via “grafting through” technique and were applied as model sorbents to understand physisorption and chemisorption of carbon dioxide molecules. The expe
We obtained the reaction mechanism of cerium with oxygen by means of density functional theory (DFT) under the explosive or detonation situation. The energy level order of cerium was calculated and the potential energy profile was plotted. The properties
BaTiO3/epoxy composites consisting of two three-dimensionally interpenetrating networks of BaTiO3 and epoxy phases were prepared using a new approach. The BaTiO3/epoxy composites exhibit a colossal dielectric constant, low dielectric loss and high flexura
A high production efficiency synthesis method was used to produce a stacked vanadium nitride nanoparticle structure with an inexpensive raw material as an anode material and high surface area polystyrene was used the cathode material for lithium ion hybri
Polymer-based composite was investigated by embedding calcium copper titanate (CaCu3Ti4O12;CCTO) fillers into polytetrafluoroethylene(PTFE) matrix.The dielectric performances of the composite were investigated within the frequency range fiom 100 Hz to 1 M