Dielectric Properties of Polytetrafluoroethylene/CaCu3Ti4O12 Composites

来源 :武汉理工大学学报(材料科学版)(英文版) | 被引量 : 0次 | 上传用户:bingdongfenxing
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Polymer-based composite was investigated by embedding calcium copper titanate (CaCu3Ti4O12;CCTO) fillers into polytetrafluoroethylene(PTFE) matrix.The dielectric performances of the composite were investigated within the frequency range fiom 100 Hz to 1 MHz.It is indicated that dielectric permittivity (ε) and dielectric loss (tanδ) increase gradually as the filler content increases.Dielectric permittivity for the composite with 50 vol% CCTO filler loading is 33.5,approximately 16 times higher than that of pure PTFE (ε =2.1) at 100 Hz.As the frequency increases,the dielectric loss decreases rapidly and reaches stability,and then remains low when the frequency rises to 1 MHz.The values for dielectric permittivity and dielectric loss in the microwave frequency (8-13GHz) are lower than that in low frequency of 10 kHz for the composites because of different polarization modes.Several theoretical models were implemented to compare the experimental results with the theoretical calculations and the modified Lichtenecker equation was found to fit the best.
其他文献
The formation and growth behavior of intermetallic compound (IMC) layers after introducing an electroless Ni-W-P metallization into the Sn-3.0Ag-0.5Cu (SAC305) solder joint during soldering and aging were investigated.The soldering was performed at 250 ℃
The Z-type ferrites of nominal composition Ba3Co2Fe24O41+x wt% Bi2O3, where x=0.25, 0.5, 1.0, 1.5, 2.0, were prepared by conventional ceramic processes. The influence of Bi2O3 content on the bulk densities, microstructures, magnetic and dielectric propert
A novel fiber optic sensor based on optical composite oxygen-sensitive film was developed for determination of 2,4-dichlorophenol (DCP). The optical composite oxygen-sensitive film consists of tris(2,2\'-bipyridyl) dichloro ruthenium(II) hexahydrate (Ru
The microstructure and texture evolution of Fe-33Mn-3Si-3Ai twinning induced plasticity (TWIP) steel were studied by the scanning electron microscope (SEM) and X-ray diffraction (XRD) at room temperature.After quasi-static tensile,the texture evolution of
Different failure modes and morphologies were found in the chemical vapor infiltration (CVI) 2D C/SiC torque tubes with different thickness. To characterize the density and porosity of the ceramic matrix composite (CMC) torque tube, a CT test was conducte
A novel low temperature co-fired ceramic (LTCC) material was fabricated by zinc titanate (ZnTiO3) ceramics doped with B2O3-BaO-SiO2-ZnO-Li2O (BBSZL) glass. The influences of BBSZL glass on wetting behavior, sintering activation energy, phase composition,
Amine-functionalized imidazolium-based poly(ionic liquid) brushes on mesoporous silica were synthesized via “grafting through” technique and were applied as model sorbents to understand physisorption and chemisorption of carbon dioxide molecules. The expe
We obtained the reaction mechanism of cerium with oxygen by means of density functional theory (DFT) under the explosive or detonation situation. The energy level order of cerium was calculated and the potential energy profile was plotted. The properties
BaTiO3/epoxy composites consisting of two three-dimensionally interpenetrating networks of BaTiO3 and epoxy phases were prepared using a new approach. The BaTiO3/epoxy composites exhibit a colossal dielectric constant, low dielectric loss and high flexura
A high production efficiency synthesis method was used to produce a stacked vanadium nitride nanoparticle structure with an inexpensive raw material as an anode material and high surface area polystyrene was used the cathode material for lithium ion hybri