【摘 要】
：
Ni-Mo-P coatings are obtained at the surface of ceramic substrate by electroless deposition using palladium as a surface catalyst.The influence of catalyst activation conditions on coatings\' properties was assessed by structural,morphological,electrica
【机 构】
：
Department of Materials and Mechanical Engineering,Universitat Politècnica de València, Valencia, Sp
论文部分内容阅读
Ni-Mo-P coatings are obtained at the surface of ceramic substrate by electroless deposition using palladium as a surface catalyst.The influence of catalyst activation conditions on coatings\' properties was assessed by structural,morphological,electrical,mechanical measurements and adhesion strength by using X-ray diffraction,field emission scanning electron microscopy,atomic force microscopy,Hall effect and nanoindentation techniques,respectively.The results indicated the formation of dense,continuous and uniform coatings consisting mainly of Ni.The coatings obtained at 300 ℃ for 12 h exhibited the best electrical properties,namely resistivity of 9.32 μΩ cm,smaller roughness (Ra 0.090 μm) and average mechanical properties.The adhesion tests showed a firm adherence of the Ni-Mo-P coatings to the ceramic surface.The results of this study could offer an approach for obtaining conducting ceramic substrates in order to be employed in photovoltaic applications.The performance of demonstrative heterojunction solar cell obtained with such metallized ceramic is indicative of the high potential of the Ni-Mo-P electroless coatings for functional ceramics.
其他文献
Construction of suitable structural models in order to account for chemical short-range orders is the reason behind the difficult multi-scale computational simulation methods for solid solutions.Herein,using Ti-Mo alloys as representative,we used our clus
FeAlCuCrNiMo0.6Tix (x =0.2,0.6,0.8) high-entropy alloys were fabricated with flux-cored wire and surfaced on low-carbon steel by gas metal arc welding.The effect of Ti addition on the microstructures and properties of FeAlCuCrNiMo0.6Tix HEAs surfacing lay
Ti-Ta alloys have been widely studied for biomedical applications due to their high biocompatibility and corrosion resistance.In this work,nearly fully dense and in situ alloyed Ti-50 wt％ Ta samples were fabricated by the laser powder bed fusion (LPBF) of
The effect of stacking fault energy (SFE) on the grain structure evolution of face-centered cubic metals during friction stir welding was investigated by using pure aluminum,pure copper and Cu-30Zn alloy as experiment materials.Tool “stop action” and rapi
The NiTi cladding with/without Ni interlayer was prepared on stainless steel (SS) by tungsten inert gas (TIG) surfacing process,aiming at achieving good cavitation erosion resistance.The ranking according to the cavitation erosion resistance is NiTi plate
A systematic study on the wettability and interactions between superalloy melts with various Re contents and Al2O3-based ceramic moulds was presented in this paper.It was found that the increase of Re content inhibited the interfacial reactions to some ex
The microstructure and fracture toughness of weld metal under Ti-free and Ti-containing different fluxes were investigated in this study.It was found that the trace element Ti of flux in submerged arc welding produced significant influence on the fracture
Optimization of grain boundary engineering (GBE) process is explored in a Fe-20Cr-19Mn-2Mo-0.82 N high-nitrogen and nickel-free austenitic stainless steel,and its intergranular corrosion (IGC) property after GBE treatment is experimentally evaluated.The p
The inclination angle of the flake particle has a significant impact on the in-plane thermal conductivity of composites.The graphite flake/Al composites (50 vol％) with different inclination angles were fabricated via flake powder metallurgy,and the result
High-strength,corrosion-resistant,and lightweight Al-Mg alloys perform an important function in harsh coastal service environments.Corrosion resistance is generally inversely correlated with strength;hence,it is difficult to simultaneously optimize both.I