【摘 要】
：
FeAlCuCrNiMo0.6Tix (x =0.2,0.6,0.8) high-entropy alloys were fabricated with flux-cored wire and surfaced on low-carbon steel by gas metal arc welding.The effect of Ti addition on the microstructures and properties of FeAlCuCrNiMo0.6Tix HEAs surfacing lay
【机 构】
：
School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870, Chi
论文部分内容阅读
FeAlCuCrNiMo0.6Tix (x =0.2,0.6,0.8) high-entropy alloys were fabricated with flux-cored wire and surfaced on low-carbon steel by gas metal arc welding.The effect of Ti addition on the microstructures and properties of FeAlCuCrNiMo0.6Tix HEAs surfacing layer was systematically studied.The results show that FeAlCuCrNiMo0.6Tix HEAs surfacing layer exhibits a majority of BCC solid solution based on Fe-Cr phase and a small amount of MC phase.Microhardness and wear tests results show that the addition of Ti can significantly improve the microhardness and wear resistance of the surfacing layer.The microhardness of surfacing layer can reach up to 642 HV0.5,which is about 2.8 times that of the substrate.Meanwhile,the wear mass loss is minimum.Electrochemical corrosion test results show that the addition of Ti can improve the corrosion resistance of surfacing layer,which is better than 304 stainless steel substrate.With the increase in Ti,the corrosion resistance increases first and then decreases.When the Ti content is 0.6,the self-corrosion current density of polarization curve is the smallest,the capacitive impedance radius of electrochemical impedance spectroscopy is the largest,and the corrosion resistance effect is the best.
其他文献
A new Mg-2.2 wt％ Zn alloy containing 1.8 wt％ Ca and 0.5 wt％ Mn has been developed and subjected to extrusion under different extrusion parameters.The finest (～ 0.48 μm) recrystallized grain structures,containing both nano-sized MgZn2 precipitates and αt-M
At room temperature,crystalline Mg-based alloys,including Mg2Ni,MgNi,REMg12 and La2Mg17,have been proved with weak electrochemical hydrogen storage performances.For improving their electrochemical property,the Mg is partially substituted by Ce in Mg-Ni-ba
In order to study the corrosion resistance of extruded magnesium alloys,the Mg-4Zn-2Gd-0.5Ca alloy was extruded at the speed of 0.01-0.1 mm/s with the temperature of 280-360 ℃ in present study.Hot extrusion results show that the volume fraction of precipi
AlCoCrFeNi is one of the most widely studied alloy systems in the high-entropy alloy (HEA) area due to the interesting microstructure and mechanical properties.In this study,the A1CoCrFeNi alloy was prepared using spark plasma sintering (SPS) with pre-all
The corrosion behaviour of 316L and Alloy 625 was investigated using cyclic polarization,electrochemical impedance spectroscopy,X-ray photoelectron spectroscopy,Auger electron spectroscopy and induced coupled plasma-optical emission spectrometer.The resul
High-entropy alloys (HEAs) are a new class of materials with a potential engineering application,but how to obtain ultrafine or nano-sized crystal structures of HEAs has been a challenge.Here,we first presented an equiatomic CoCrFeNiCu HEA with excellent
A 444-type heat-resistant ferritic stainless steel containing 0.05 wt％ Ce (rare earth element) and 2 wt％ (Mo + W) was adopted as an experimental material to study the effect of finish rolling temperature on microstructure and texture evolution as well as
The kinetics of isothermal austenite (γ)-to-ferrite (α) transformation at various temperatures in Fe-2Mn and Fe-2Mn-0.5Mo (wt％) alloys is investigated via dilatometry experiments and phase-field modeling.It was interestingly found that Mo addition has a m
In order to improve the interface wettability as well as the interfacial bonding between graphene and copper matrix,in this work,graphene nanoplates modified with nickel nanoparticles (Ni-GNPs) were synthesized using a one-step method based on spray-dryin
Construction of suitable structural models in order to account for chemical short-range orders is the reason behind the difficult multi-scale computational simulation methods for solid solutions.Herein,using Ti-Mo alloys as representative,we used our clus