【摘 要】
：
To investigate the variation in the degree of polymerization calcium aluminium silicate hydrate (C-A-S-H) gel and its role in the evolution of the strength of waterglass slag binders, the compressive strength, hydration products, degree of hydration of th
【机 构】
：
College of Chemical and Biological Engineering, Shandong University of Science and Technology, Qingd
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
To investigate the variation in the degree of polymerization calcium aluminium silicate hydrate (C-A-S-H) gel and its role in the evolution of the strength of waterglass slag binders, the compressive strength, hydration products, degree of hydration of the slag, and the degree of polymerization of C-A-S-H gels of binders were examined. The experimental results indicate that the pH of the pore solution increased with an increase in the Na2O concentration. However, mortar with an optimum compressive strength value of 81.0 MPa at 28 d was obtained when water glass modulus was 1.5. The main hydration product is a C-A-S-H gel for which the quantity and the degree of polymerization depend strongly on the Na2O concentration; for a given range, both increase with increasing Na2O concentration, thus yielding an enhanced strength. A further increase in the Na2O concentration continuously increases the quantity of C-A-S-H gels while drastically reducing the degree of polymerization. The positive effect of the former is counteracted by the adverse effect of the latter, ultimately, leading to a decreased strength. Furthermore, we reveal that the degree of polymerization for C-A-S-H gels may be affected by pH, through a series of complex chemical reactions.
其他文献
Nano-pellet α-Al2O3 was prepared using aluminum nitrate as precursor and urea as fuel by a fast method of solution combustion synthesis. The formation of the nano material was dependent on the molar ratio of fuel/oxidant, calcination temperature, and fore
Aluminum sol, dry gel, and film were prepared by sol-gel and a dipping-withdrawing method. The effect of polyethylene glycol (PEG) on the behavior of aluminum sol, gel, and film was investigated by DLS, rotary viscometer, XRD, IR, EPMA, and light microsco
A quantitative pH measuring method has been used to measure the pH of pure and blended cement mortars. The blended cement mortars incorporating supplementary cementitious materials (SCMs) such as fly ash (FA), ground granulated ballast furnace slag (GGBFS
With the risk of disappearing for the rock paintings considering long-term exposure in Helan Mountain, the freeze-thaw(F-T) cycling experiments were carried out with 12-hour F-T cycling (0, 10, 20, 30, and 40 F-T cycles) under five kinds of confining pres
TiSi2 reinforced boron phenolic composites (TP) and Vitreous silica fabric reinforced TiSi2/boron phenolic composites (VTP) were prepared by compression molding, and their thermal, mechanical, ablation properties were studied. TG results show that thermal
In order to facilitate self-compacting concrete to be better used in tunnel linings that can resist fires, a SiO2 aerogel-cement mortar coating was prepared. Based on the HC curve, a self compacting concrete cube specimens coated and uncoated with SiO2 ae
To reveal and utilize the interaction between Tamm plasmon polaritons (TPPs) and two-dimensional materials are promising for exploiting next-generation optoelectronic devices. Herein, the coupling mechanism between metal TPPs and monolayer WS2 along with
Hydration-heat-inhibiting materials(HIM) with polysaccharide as core material was prepared using microcapsule sustained-releasing technology, through a centrifugal spray granulation process after melting together. The preparation process parameters of HIM
A molecular modified PCE-type GA was self-synthesized, and the grindability concerning grinding duration and particle size distribution of ground cement was evaluated. Setting time, flowability, hydration heat, mechanical properties and microstructure of
Bituminous binders have been modified by using cocamide diethanolamide. The chemical material used in this study is used for the first-time on the purpose of modification of the bitumen. In addition to the conventional bitumen tests (penetration, softenin