• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Impact Force Identification and Damage Monitoring of Cfrp Sandwich Panels

Impact Force Identification and Damage Monitoring of Cfrp Sandwich Panels

来源 :The 11th China-Japan joint conference on Composite Materials | 被引量 : 0次 | 上传用户：dc365
【摘 要】
：
This paper examines a method for identifying the location and force history of an impact acting on a CFRP sandwich panel by using the strain responses measured with built-in sensors.
【作 者】
：
Satoshi Atobe Ning Hu Hisao Fukunaga 
【机 构】
：
Department of Aerospace Engineering,Tohoku University
【出 处】
：
The 11th China-Japan joint conference on Composite Materials
【发表日期】
：
2014年3期
【关键词】
：
Structural Health Monitoring Impact Force Identification Impact Damage Sandwich 
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　This paper examines a method for identifying the location and force history of an impact acting on a CFRP sandwich panel by using the strain responses measured with built-in sensors.
其他文献
蒙脱土对PLA/PBAT共混体系微观形貌的影响
通过熔融共混法制备聚乳酸(PLA)/聚对苯二甲酸-己二酸-l,4-丁二醇共聚酯(PBAT)/有机蒙脱土(OMMT)三元共混物,研究了不同加工条件下,蒙脱土纳米粒子对共混物微观形貌的影响,并结合纳米粒子选择性分布效应对其增容机理进行了初步探时。
会议
聚乳酸PBATOMMT选择性分布增容
低成本大尺寸镁基复合材料的制备技术
采用超声波辅助搅拌铸造的方法，成功制备了碳化硅质量分数为20％的大尺寸镁基复合材料，铸锭的质量大约为21千克.与基体合金相比，复合材料的力学性能得到了明显提升.在复合材料的不同位置，碳化硅颗粒均匀分布，各部位的含量相同.但是，从微观结构上来看，颗粒沿着晶界呈项链状分布.在热挤压过程中，尽管部分碳化硅颗粒结构受损，但是显著改善了碳化硅颗粒在复合材料内的分布，同时进一步提高了材料的力学性能.T6处理材
会议
搅拌铸造大尺寸复合材料热挤压T6处理
冷热循环对M40级碳纤维缝编织物/环氧复合材料力学性能的影响
使用高韧性环氧树脂R608通过RTM工艺制备了M40级碳纤维缝编织物/环氧复合材料。对M40级碳纤维缝编织物/环氧复合材料进行-196℃到80℃冷热循环试验,并对其100次和300次冷热循环前后力学性能和微观形貌进行了测试。结果显示,100次冷热循环后,拉伸性能、弯曲性能、压缩性能、层间剪切和冲击性能略微增加或降低,而300次冷热循环后,这些力学性能基本趋于稳定。总的来说,与冷热循环前相比,M40
会议
冷热循环复合材料RTM力学性能应力
Characterization of the Injection Conditions on the Electrical Conductivity of Mwcnts/Pc Nanocomposi
Multiwalled carbon nanotubes/Polycarbonate (MWCNTs/PC) nanocomposit-es were successfully prepared by injection molding process.With the injection conditions changed,MWCNTs/PC nanocomposites with diffe
会议
Multiwalled carbon nanotubes (MWCNTs)Polycarbonate (PC)NanocompositesInjectio
结合分子模拟探讨改性PBS/纤维素衍生物复合材料的相互作用
采用聚乙二醇(PEG)改性的聚丁二酸丁二醇酯(PEG/PBS)分别与羧甲基纤维素(cMc)和羟乙基纤维素(HEC)共混制备了在水相均匀分散的聚酯/纤维素新型液体复合材料，并结合分子模拟技术对该液体复合材料间的相互作用机制进行了研究。
会议
醚化PBS纤维素衍生物液体复合材料动力学模拟相互作用
Creation of CNT/PC Nanocomposite and Electrical Conductivity Evaluation
In the present study,according to the viewpoint of the formation mechanism of the internal microstructure of the nanocomposites samples in the injection molding,the effects of the contents of carbon n
会议
Carbon nanotube(CNT)Polycarbonate(PC)NanocompositesInjection conditionsSurfa
Development of Polymer Based Electromagnetic Shielding Materials
The development of EMI shielding materials is receiving increasing attention recently since the higher speed communication resulted in the higher frequency range of electromagnetic waves and this will
会议
Electromagnetic interfernece (EMI)Shielding effectiveness (SE)LaminatesDielec
Dynamic Stress Distribution of Composite Materials Using Ultrasonic Wave Propagation
A method combining the evaluation of dynamic stress distribution and ultrasonic wave propagation analysis for composite materials is presented.By using two-dimensional time domain finite element analy
会议
Bimaterial compositesStress concentrationFree-edge effectsTime-domain Finite
Effect of Surface Treatment on Bending Properties of Recycled Carbon Fiber Reinforced Plastic
Carbon fiber reinforced plastic (CFRP) composites were recycled using superheated steam.Recycled carbon fibers were surface treated for reuse as fiber-reinforced plastic (FRP) composites.
会议
CFRPRecyclingSurface TreatmentMechanical propertiesSuperheated steam
Investigation of Deterioration of Material Properties in Cfrp Due to Impact Damage
Impact loading was given to CFRP plates by a drop-weight impact testing machine in order to investigate development of internal damage and its effects on variation of material properties.
会议
CFRPImpact DamageThermal ConductivityYoung's ModulusDelaminationTransv