【摘 要】
：
Spherical Nb-20Si-24Ti-2Cr-2Al pre-alloyed powders were processed by selective laser melting (SLM) on Ti6Al4V substrates with different energy densities.A series of single tracks and single layers were produced using different processing parameters,includ
【机 构】
：
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
论文部分内容阅读
Spherical Nb-20Si-24Ti-2Cr-2Al pre-alloyed powders were processed by selective laser melting (SLM) on Ti6Al4V substrates with different energy densities.A series of single tracks and single layers were produced using different processing parameters,including powder size,laser power,scanning speed and hatch distance.Results showed that the pre-alloyed powders ranging from 45 to 75 μm were more applicable to SLM with less balling tendency,in comparison with those between 75 and 180 μm.The increase in linear energy density (LED) resulted in the decrease in contact angle and the increase in the width of single track as well as its penetration depth into the substrate.Smaller hatch distance leaded to a larger remelted part of the former track and a higher volumetric laser energy density.With a thickness of 75.6 μm,an interfacial intermediate layer,enriched in Ti and depleted in Nb,Si,Cr and Al,was formed between the SLM part and the Ti6Al4V substrate.The mechanisms of the elimination of balling phenomenon by employing a higher LED and the interfacial bonding characteristics between Nb-Si-based alloys via SLM and the Ti6Al4V substrate were discussed.
其他文献
The morphological evolution of Fe-rich phases in the AlSi9Cu3Mg0. 19(Fe) alloy has been investigated with various contents of Fe, Mn, and Cr. The results show that coarse Chinese script Fe-rich phases appear in the alloy with 0. 6 wt％ Fe combined with tra
Magnesium matrix composites reinforced with AlN particles were fabricated by the powder metallurgy technique. Different mixing methods were used in this study to control the distribution of AlN particles. The microstructure, thermal diffusivity and therma
A facile polyol-assisted pyro-synthesis method was used to synthesize Co3O4 nanoparticles embedded into carbon matrix without using any conventional carbon source.The surface analysis by scanning electron microscopy showed that the Co3O4 nanoparticles (～2
A polymethyltrimethoxysilane (PMTMS)/hydroxyapatite (HA) hybrid coating was successfully fabricated on a magnesium alloy by hydrothermal treatment and immersion method.The microstructure and composition of the coating were characterized by using X-ray dif
The growth behavior of Al3Ni intermetallic compounds (IMCs) during the directional solidification of Al-10 wt％ Ni alloy was investigated by synchrotron radiography. Two main growth patterns of primary Al3Ni phase, I-like and V-like, appeared during solidi
Sand-cast Mg-9Gd-4Y-0.5Zr (wt％) alloy was solution-treated at 500-565 ℃ in the time range of 0.5-30 h in air or vacuum to investigate its microstructure evolution and mechanical properties.The results showed that solution treatment temperature had a signi
The different solution and migration behaviors of tetrahedral and octahedral interstitial helium in bcc iron have been investigated by using first principles calculations.We showed that the tetrahedral site has less charge transfer and less redistribution
The Mg-8Sn-4Zn-2Al (TZA842,in wt％) alloys with different initial microstructure (as-cast-AC and homogenization treatment-HT) subjected to hot extrusion.Also,the strengthening responses to AC and HT for the extruded TZA842 alloys were reported.The results
In order to investigate the effect of microstructural characterization on the mechanical properties and retained austenite stability,a different type of quenching and partitioning steel (I-Q&P) through intercritical annealing before the quenching and part