【摘 要】
：
The Cr-Si-N coatings were prepared by combining system of high-power impulse magnetron sputtering and pulsed DC magnetron sputtering.The Si content in the coating was adjusted by changing the sputtering power of the Si target.By virtue of electron-probe m
【机 构】
：
Tianjin Key Laboratory of High Speed Cutting and Precision Manufacturing, Tianjin University of Tech
论文部分内容阅读
The Cr-Si-N coatings were prepared by combining system of high-power impulse magnetron sputtering and pulsed DC magnetron sputtering.The Si content in the coating was adjusted by changing the sputtering power of the Si target.By virtue of electron-probe microanalysis,X-ray diffraction analysis and scanning electron microscopy,the influence of the Si content on the coating composition,phase constituents,deposition rate,surface morphology and microstructure was investigated systematically.In addition,the change rules of micro-hardness,internal stress,adhesion,friction coefficient and wear rate with increasing Si content were also obtained.In this work,the precipitation of silicon in the coating was found.With increasing Si content,the coating microstructure gradually evolved from continuous columnar to discontinuous columnar and quasi-equiaxed crystals;accordingly,the coating inner stress first declined sharply and then kept almost constant.Both the coating hardness and the friction coefficient have the same change tendency with the increase of the Si content,namely increasing at first and then decreasing.The Cr-Si-N coating presented the highest hardness and average friction coefficient for an Si content of about 9.7 at.％,but the wear resistance decreased slightly due to the high brittleness.The above phenomenon was attributed to a microstructural evolution of the Cr-Si-N coatings induced by the silicon addition.
其他文献
The reliability of a substrate curvature-based stress measurement method for CrN thin films on substrate with fluctuant surface was discussed.The stress error led by the ignorance of substrate thermal deformation was studied.Results showed that this error
Using the methods of transmission electron microscopy,the carbide phase evolution in surface layers of the differentially quenched rails is studied after the passed tonnage of 691.8 million tons at the depth up to 10 mm along the central axis and fillet o
The effect of heat treatment on the microstructures and mechanical properties of a newly developed austenitic heat resistant steel (named as T8 alloy) for ultra-supercritical applications have been studied.Results show that the main phases in the alloy af
A reaction interface between the aluminum and K2ZrF6 during molten salt reaction process was frozen by quenching the mold in water,and the interface structure was analyzed to determine the formation process of Al3Zr.Results show that a clear conical inter
A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts: the Ti-Al intermetallic multilayered composite and continuous SiC fibers-reinforced Ti matrix composite. In the Ti-A
Electropulsing-induced phase decompositions and microstmctural changes in AZO-5 thin films were studied by X-ray diffraction,scanning electron microscopy,atomic force microscopy,Hall effect measurement and photoluminescence (PL)measurement techniques.It w
The effect of cryorolling on the precipitation process of deformed Cu-Ni-Si alloys was investigated through in situ synchrotron X-ray diffraction technique.The results demonstrate that the precipitation process is significantly accelerated by cryorolling.
The microstructures and corrosion behaviors of AA2198-T851 alloy and weld were analyzed under corrosive conditions.Weld was formed using an innovative fiber laser welding process with AA2319 Al-Cu filler wire.The metallurgic morphology and distribution of
Microstructures and oxidation behaviors of four Dy-doped Nb-Si-based alloys at 1250 ℃ were investigated.The nominal compositions of the four alloys are Nb-15Si-24Ti-4Cr-2Al-2Hf-xDy (at.％),where x =0,0.05,0.10 and 0.15,respectively.Results showed that the
This study reports that small amounts of MoO3 multilayer ribbon crystal (MoO3 MLRC) in Ni3Al intermetallics showed the decreased friction coefficients and improved wear resistance at different contact loads.Specifically,the friction coefficients (0.32-0.3