【摘 要】
：
The integration of micro-electro-mechanical system (MEMS) with metamaterial has provided a novel route to achieve programmability via its reconfigurable capabilities. Here, we propose and demonstrate a MEMS-based metadevice by using switchable winding-sha
【机 构】
：
SchoolofElectronicsandInformationTechnology,SunYat-senUniversity,Guangzhou510006,China
【出 处】
：
PhotonicsResearch
论文部分内容阅读
The integration of micro-electro-mechanical system (MEMS) with metamaterial has provided a novel route to achieve programmability via its reconfigurable capabilities. Here, we propose and demonstrate a MEMS-based metadevice by using switchable winding-shaped cantilever metamaterial (WCM) for active logical modulation. WCM can be actuated by external driving voltage, and the logical modulation bit is performed by releasing MEMS cantilevers to represent “on” and “off” states. While the underneath substrate surface of a MEMS-based metadevice is rough after releasing the cantilevers, the metadevice is allowed to operate on the reconfigurable switching state and avoid the snapping down of the device when the system is overloaded. Such a reconfigurable and programmable MEMS-based metadevice exhibits multifunctional characteristics to simultaneously perform the logic operations of “OR” and “AND” gates. By exploiting the tuning mechanism of the MEMS-based metadevice, the arbitrary metamaterial configuration can be implanted into WCM. This opens a wide avenue to further enlarge the operating frequency range and applications in optoelectronic fields. These unique results provide various possibilities in multifunctional switching, active logical modulating, and optical computing applications.
其他文献
In this paper, we propose and numerically investigate a novel circular lattice photonic crystal fiber (CL-PCF) using controllable GeO2 doped silica, suitable for modes carrying quantized orbital angular momentum (OAM). Large effective index sep
The influence of p-type GaN (pGaN) thickness on the light output power (LOP) and internal quantum efficiency (IQE) of light emitting diode (LED) was studied by experiments and simulations. The LOP of GaN-based LED increases as the thickness of pGaN layer
研究了仪器函数形状稍微偏离对称三角形情形下的三刺激值计算问题,探索了其对应的最优加权表。结果发现,最优权重可以通过求解三个系数矩阵的线性方程组来得到,且系数矩阵是对称正定三对角矩阵。将本课题组前期研究获得的最优加权表方法推广到仪器函数形状为非对称三角形的情形。仿真结果表明,对于10 nm和20 nm测量间隔,最优加权表方法的精度优于三点和五点校正方法;对于5 nm测量间隔,最好的计算方法是先对测量数据进行三点校正,再使用直接选取方法计算三刺激值。
就几种典型的情况,计算注入型法布里-珀罗腔的参数与输出光束参数的关系,法布里-珀罗腔的频谱特性及时间弛豫效应,并指出这些特性在激光光谱研究领域中的应用前景.
采用琼斯矩阵进行系统偏振分析，提出了一种基于全内反射的偏振相位差快速测量方法。采用光学薄膜特征矩阵理论对薄膜进行光学特性分析，导出了通过测量全内反射偏振相位差以获取体材料折射率以及膜层厚度的关系式。实验采用该方法获得了K9玻璃的色散曲线，分析了其膜层厚度的监控灵敏度，并与透射率监控方式进行比较。研究结果表明：采用该方法获得的K9玻璃色散曲线与标准曲线非常吻合；该方法相较于透射率监控具有更高的厚度监控灵敏度和折射率测量精度。
The emergent light distribution of a new type of contact laser scalpel is measured in three different states using a light sensor. The relationship between the angle and the light intensity is analyzed. The results show that the strongest light is emitted
以非稳腔为振荡器谐振腔,比较了振荡器、行波放大和注入振荡放大几种方式运转的铜蒸气激光器输出光束的功率和方向性,实验结果表明注入振荡放大是最佳的结构,其效率比振荡器高30％,方向性提高的倍数(4.5倍)与几何光学的预计大致相符。
干涉仪参考镜面形离焦误差难以精确标定，是导致拼接累积效应、制约平面子孔径拼接系统检测精度的主要因素。推导了参考镜离焦与拼接累积误差、拼接次数间的定量表达式，基于该表达式在拼接过程中标定并去除参考镜离焦误差，降低拼接累积误差。对450 mm×60 mm 的平面镜进行了8个子孔径的拼接检测，与大口径干涉仪检测结果比对，去除参考面离焦误差前后拼接测量误差峰谷(PV)值从λ/10减小至λ/30，有效提高了拼接测量精度。结合绝对检验技术标定参考镜高阶面形误差，验证了离焦是引起拼接误差累积的主要因素，消除参考镜高阶面