超过滤法测定有机显色剂在胶束——水相的分配系数

来源 :分析试验室 | 被引量 : 0次 | 上传用户:wangyongahz4
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
本文首次用超过滤法测定了有机显色剂CAS、PAR、TAMB、BTAMB.金属离子Ni(?)和Ni(Ⅱ)-TAMB配合物在SDBS、SDS、CTMAB、Triton X-100、Brij35及PeregalO等胶束溶液中的分配系数。较详细地研究了超过滤条件,根据所得数据,并将其与相应光度体系的行为进行了比较。得出了一些有意义的结论。文中还利用分配系数定义式,推得了旨在计算溶质在胶束一水相分配比值的方程,并将所得结果与光度体系中配合物在胶束存在下的褪色现象,最佳表面活性剂用量范围与配合物稳定常数关系进行了比较.得出了一些结论和规律。 In this paper, the organic chromogenic agents CAS, PAR, TAMB and BTAMB were determined by ultrafiltration method for the first time.The complexes of Ni (Ⅱ) -TAMB and Ni (Ⅱ) -TAMB were immobilized on SDBS, SDS, CTMAB, Triton X-100, Brij35 and PeregalO Such as micellar solution in the partition coefficient. The ultrafiltration conditions were investigated in more detail and based on the data obtained, their behavior was compared with that of the corresponding photometric system. Come to some meaningful conclusions. In this paper, we also use the definition of partition coefficients to deduce the equation that is used to calculate the ratio of solute to water in micelles, and the results obtained are in agreement with the fade phenomenon of the complex in the photometric system in the presence of micelles. The optimum amount of surfactant The relationship between the stability of the complex and the complex was compared. Some conclusions and laws were obtained.
其他文献
一、轧尖机1.用途:在钢丝穿模时用轧尖机将线材或钢丝端头锻细。2.分类:按原理分有两种类型,即锻打式和压延式。(1)迥转式锻尖机(一般叫旋锤)——锻打式 First, the rollin
我厂生产的汽轮机主汽门的15Cr11MoV钢阀杆、阀碟等零件,氮化后要求 HV≥650,渗层深度≥0.30mm,脆性≤3级。原采用普通氮化:530±10℃×20h,氨分解率25~30%;600±10℃×37h,
迄今,在金的萃取化学研究中,以中性含氧萃取体系为最多。我们曾对含有碳氧、硫氧和磷氧的萃取剂对金的萃取作过报道,新近,又有芳香氮氧化物用于金和铂族金属的萃取研究和金
本文就ISO关于分析试剂中砷的测定的一般方法作了理论上的详细说明。 This paper gives a detailed description of the general method of ISO for the determination of a
利用磷钼杂多酸测磷,这是众所周知的,但用于钼的测定,还未见报道。本文提出在含MoO_4~(2-)溶液中,过量PO_4~(3-)的存在下使之形成磷钼杂多酸,经抗坏血酸还原后,直接用于钼的
人们对于旅游的需求,近年来呈上升趋势,带动了我国旅游业的迅猛发展。海南作为我国旅游的热门城市,其丰富的旅游资源使其在竞争中占据绝对优势,但也不乏存在一些问题。论文简
附图所示磨直齿齿轮的夹具,在生产实践中证明是可靠的。当把齿轮(工件)装入后,用铜棒轻轻敲击几下,夹具的周边即可把齿轮准确地定心夹紧。制造该夹具时要注意使三个偏心凸块
国家科委于1991年5月27日正式批准建立了“苏锡常火炬开发带”,这是一个不同于国家已批准的所有开发区的一种新的高新技术开发带,是我国高新技术开发区建设的一种新模式。目
铅浴处理(焙墩)具有强度高、塑性好的优点,从而能够通过较大的压缩率把钢丝冷拉到所要求的成品尺寸和达到综合的机械性能,这特别适合于以高强度为特征的钢丝品种的生产,例如