【摘 要】
：
Low-cost porous calcined dolomite microspheres were prepared by simple spray drying and subsequent calcination. Effects of calcination temperature on phase evolution and adsorption properties of MB were investigated systematically. Results showed that mic
【机 构】
：
State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineerin
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Low-cost porous calcined dolomite microspheres were prepared by simple spray drying and subsequent calcination. Effects of calcination temperature on phase evolution and adsorption properties of MB were investigated systematically. Results showed that microspheres treated at 400 ℃ kept mainly calcium carbonate (CaMg (CO3)) phase with some small pores, showing better removal efficiency for MB. With the dosage of 20 g/L under the starting concentration of 100 mg/L, the removal efficiency of the microspheres reached 95.6％. The adsorption kinetics data followed the pseudo-second-order kinetic model, and the isotherm data fit the Langmuir isotherm model. The low-cost microsphere could be applied as a promising absorbent for dyes in wastewater filtration and adsorption treatment.
其他文献
La0.8Sr0.2MnO3 samples with rhombohedral, orthohombic and monoclinic structures were prepared by solid state reaction, sol-gel and co-precipitation methods, respectively. Lattice parameters, grain size, morphology, infrared absorption and emissivity of sa
Catalyst enhanced chemical vapor deposition of nickel film on high Tg polymers such as teflon (PTFE), polyimide(PI), and polysulfone(PS) was investigated by hot wall and cold wall CVD, in which Ni(dmg)2, Ni(acac)2, Ni(hfac)2, Ni(TMHD)2, and Ni(cp)2 are us
Nano-ZrO2 and PEEK particles were synergistically filled in unfilled PTFE to improve the wear resistance and maintain a relatively low friction coefficient, and the materials were studied using a reciprocating sliding friction and wear tester. In the fric
A post-treatment of hydrothermal process was conducted to evaluate its effects on the material characteristics and mechanical properties of plasma-sprayed pure HA and HA/20％ YSZ coatings. Surface morphology and microstructural changes, relative element co
The polymeric admixture,the sodium-carboxymethylcellulose (CMC)/poly sodium p-styrene sulfonate (PSS) / poly vinyl acetate (PVAc) was synthesized and applied in cement mortars.The polymer was tested by FTIR and SEM,and the results indicate that the ideal
The nucleation process of graphene films prepared by pulsed laser deposition has been investigated in detail. It is found that graphene nucleates at the steps on the substrate surface firstly, from aggregation of nuclei into particles. High pulsed laser e
In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide (SiC) -based fibers, specified as XD-SiC fibers (low oxygen) and Nicalon-201 fiber
A recrystallization and partial melting (RAP) process was introduced to prepare the semi-solid 7075 aluminum alloy used for thixoforming. In order to obtain an ideal semi-solid microstructure, a series of extrusion experiments were conducted to comparativ
A plasma cladding experiment was carried out to investigate the characteristics(surface hardness, microstructure, friction, wear properties from different substrates to the cladding layer and the bond strength) of plasma cladding Fe-Cr-Nb-Si-Mo alloy clad
The 0.6mol％ CuO-doping 0.996(0.95Na0.5K0.5NbO3-0.05LiSbO3)-0.004FeBiO3 (KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric properties dependence of sintering time in KNN-LS-BF-CuO