【摘 要】
:
TMSi2 (TM =Ta,Mo) are extensively used as thermal emissivity agents in high emission coatings due to their well-known “high” emissivity in infrared range.However,there is a paucity of the high temper-ature (HT) emissivity property of these two silicides.M
【机 构】
:
Science and Technology on Advanced Functional Composite Laboratory,Aerospace Research Institute of M
论文部分内容阅读
TMSi2 (TM =Ta,Mo) are extensively used as thermal emissivity agents in high emission coatings due to their well-known “high” emissivity in infrared range.However,there is a paucity of the high temper-ature (HT) emissivity property of these two silicides.Moreover,room temperature (RT) spectrometer measurements have demonstrated that the emittance in infrared range of two silicides was considerably low.Therefore,providing critical HT data and satisfactory elucidation on the emission incompatibility of TMSi2 is eagerly needed.In this contribution,combining first principles calculations and Drude model,the reflectance spectra of TMSi2 were predicted at both RT and HT.Consistent with spectrometer mea-surements,the intrinsic emittance of silicides was relatively low in the entire investigated temperatures.To explain the incompatible emission behavior,two simplified models including the majority of high emissivity coating,SiO2,were proposed.Intriguingly,with SiO2 considered in simulations,no matter covered on the surface or blended in the composites,the emittance of the TMSi2 enhanced significantly.Our theoretical results demonstrate the non-negligible significance of oxides on the high temperature performance of silicides and provide the guidelines for improving the emission performance of silicides and searching for potential high emissivity agents.
其他文献
In this work,bending fatigue behavior of thinner Zr61Ti2Cu25Al12 (ZT1) BMG beams with thicknesses of 500 μm and 100 μm were investigated with three-point bending (3PB),to evaluate the reliability and safety of this potentially material used in compliant m
A laser texturing technique herein can endow bare aluminum alloy surface with regular dimple-pattern array and thus generates a case hardening.After STA treatment,these laser-textured samples become superhydrophobic.The surface wettability of the laser-te
The discovery of band convergence has opened an effective avenue for significantly enhancing thermo-electric performance of SnTe,while alloying CdTe in SnTe is evidenced efficient for improving the valley degeneracy.However,the thermoelectric transport pr
Among the various anodes,Li3VO4 is a potential intercalation kind anode used in lithium-ion batteries(LIBs) that exhibits safer discharge voltage and higher capacity than graphite,a lower voltage plateau than Li4Ti5O12,and smaller volume difference in the
Over recent years,eutectic high-entropy alloys (EHEAs) have intrigued substantial research enthusiasms due to their good castability as well as balanced strength-ductility synergy.In this study,a bulk cast Al19.25Co18.86Fe18.36Ni43.53 EHEA is developed wi
Transition-metal based hybrids with excellent stability and activity are favorable candidates for hydrogen evolution reaction (HER).The development of typical Co3S4 has recently received considerable atten-tion due to the multiple valences of the spinel-s
The phase transformation and microstructure in Ti-22Al-25Nb alloy are extremely complex.In this work,the morphology evolution of the O phase during the heating and cooling process was investigated by electron backscatter diffraction (EBSD) and first-princ
The fatigue damage behavior of the nanocrystalline Au films on polyimide substrates was investigated.It was found that the very high-cycle fatigue damage resistance of the Au film was significantly enhanced by at least a factor of ~2 in supported loading
The high-manganese steels are important structural materials,owing to their excellent toughness at low temperatures.However,the microstructural causes for their unusual properties have not adequately been understood thus far.Here,we report a reversal rela
Oxide inclusions widely exist in additively manufactured components due to the native oxide layer on the powder surface,together with gas impurities during the printing process.Using in-situ tensile tests combined with electron backscatter diffraction (EB