Evolution of TCP Phase During Long Term Thermal Exposure in Several Re-Containing Single Crystal Sup

来源 :金属学报(英文版) | 被引量 : 0次 | 上传用户:jayxiandan001
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The application and component designs of single crystal superalloys are restricted by the precipitation of topologically closed packed (TCP) phases,which can deteriorate the microstructural stability of the alloys severely.Limited researches concerning the type and morphology evolution of TCP phases under elevated temperature conditions have been reported previously.In the present work,three Re-containing single crystal alloys were designed to investigate TCP phase evolution via long term isothermal exposure tests at 1120 ℃ while the effects of Re on the microstructural characteristic and elements segregation were also clarified.The results showed that the addition of Re increased the instability of the alloys and the volume fraction of the TCP phases exceeded 5 vol% when the Re content reached 3 wt%.The increasing Re content had also raised the precipitation temperature of TCP phases but it did not change the type of them after long term aging;all the TCP particles were identified as μ phase in this study.Moreover,the elements segregation became considerably serious as Re addition increased constantly,which brought about various morphologies of theμ phase in the experimental alloys.In particular,the rod-like and needle-like μ phases demonstrated the typical orientation within γ matrix while the blockyμ phase was dispersedly distributed in the space.No specific orientation relationship could be observed in theμ phase when the addition of Re exceeded certain threshold value.
其他文献
Mg-2Al-1.2Ca-0.2Mn (at%)-based alloys with Ce-rich mischmetal (MM) substitution of 0-0.6 at% for Ca were hot extruded at 400 ℃.The effect of MM substitution on the microstructure and mechanical properties of the extruded alloys was investigated.The as-cas
The high-current pulsed electron beam (HCPEB) treatment with current density 6 J/cm2 was applied on AZ91 Mg alloy to improve its corrosion resistance.Results showed that the net-like Mg17Al12 disappeared on the surface of AZ91 Mg alloy after irradiation b
The effect of lead on the initial corrosion behavior of 316LN stainless steel has been investigated by U-bend immersion experiments in 4 wt% NaOH solutions at 300 ℃.Follow-up studies after soaking were carried out by scanning electron microscope,energy di
In this work,the effect of prior cold deformation on the stability of retained austenite in GCr15 bearing steel was investigated after quenching and tempering treatment.The thermal stability was evaluated by calculating thermal activation energy for decom
Mg AZ31/Al 7050 laminate was fabricated by co-extrusion directly from the as-cast Mg AZ31 and Al 7050 billets.The influence of annealing temperature and annealing time on microstructure and mechanical behavior of the extruded Mg/Al laminate was systematic
The AZ31 Mg alloys were processed by 6% pre-compression and frustum shearing extrusion at various temperatures,and the microstructure,texture and mechanical properties of the resulting alloys are systematically investigated.The results show that the grain
The rupture behavior of the modified 10Cr-lMo steel multi-layer welded joint is determined by the fine-grain zones of the weld metal adjacent to the fusion line during the long-term creep test at 620 ℃.The microstructures of multi-layer weld metal before
The tensile creep behavior of extruded Mg-6Gd alloy,having the tensile yield strength of ~ 110 MPa at 175 ℃,has been investigated under 175 ℃ and 150 MPa.In this study,the extruded Mg-6Gd sample exhibits the total tensile strain of ~ 10.5% after the creep
The influences of heat treatment and test condition on the microstructure and stress rupture properties of a Ni-Mo-Cr-Fe base corrosion-resistant superalloy have been investigated in this paper.Optical microscope and scanning electron microscope were empl
Enhancing combinatorial properties,such as excellent corrosion resistance,high strength and good ductility combined,is an important issue for manufacturing high-quality AlMgSi(Cu) alloys.Here,we show that this can be achieved by optimizing a combinatorial