【摘 要】
：
Steady state flow tests of different tumble intake ports matched with different S/V(surface-to-volume ratio)combustion chambers have been carried out.The results show that the flow coefficient of a me
【机 构】
：
SAIC Motor Technical Center
论文部分内容阅读
Steady state flow tests of different tumble intake ports matched with different S/V(surface-to-volume ratio)combustion chambers have been carried out.The results show that the flow coefficient of a medium tumble port is decreased by 4%,but the tumble ratio is increased by 28%in comparison with a low tumble port.The combustion chamber has little influence on intake port steady flow performance.The combustion simulation of low tumble port matched with high S/V combustion chamber has been carried out firstly,which agrees well with the test results.Base on these models,in-cylinder combustion analysis of different tumble intake port matched with different S/V combustion chamber has been carried out at 2000 rpm & full load condition.The results show that with the same combustion chamber,turbulence kinetic energy(TKE)of medium tumble port is increased by 15%,burn duration is decreased by 3℃ A,and the peak cylinder pressure is increased by 0.8MPa in comparison with low tumble port.With the same intake port,TKE of the low S/V chamber is increased by 13%,burn duration is decreased by 1℃ A,and peak pressure is increased by 0.5MPa in comparison with the high S/V chamber.The HC and soot emissions is decreased obviously but Nox is increased to some extent.The comprehensive predications show that both intake port and combustion chamber influence combustion performance of the gasoline engine significantly.The intake port has more effect on combustion behavior compared with the chamber.It is helpful to improve combustion performance by increasing tumble ratio of intake port and/or decreasing S/V ratio of combustion chamber.
其他文献
本文主要论述了在汽车门内饰板的设计开发过程中,根据由整车碰撞目标分解到车门内饰板上强度、刚度性能指标,对门内饰板上在侧面撞击过程中对应的乘员胸部和腹部碰撞区域进行优化,使其在侧面碰撞发生时上述区域能够发生必要的变形甚至破坏,并且在变形或破坏的过程中产生的反作用力从的峰值不大于一定限值以保护乘员,通过运用“静态挤压”及“动态冲撞”试验工具进行验证.通过具体车型的具体产品的实践,可以得出结论:合理布置
利用Carsim与MATLAB/Simulink联合仿真软件平台,建立了具有电动助力转向系统的整车动力学模型,设计了电动助力转向系统模型预测控制策略.仿真结果表明,所设计的控制策略的驾驶人在获得较好的助力轻便性及转向路感,保证了转向系统稳定性及车辆操纵稳定特性.
本文通过以某车型排气系统管路断裂问题为研究案例,分别从断裂管路的材质、焊接质量、管路减薄量、装配尺寸、三维模型、发动机振动分析、振动对比试验、全寿命损伤等方面进行分析,确定断裂问题根本原因为发动机传递给排气系统的振动激励过大造成,确定通过对排气系统的补偿器进行优化的方法作为此类管路断裂问题的最终解决措施,并经过耐久可靠性路试验证了解决措施的可行性.
Dynamic simulation of vehicle model in time domain with nonlinearity draws more and more attention in the world.The difficulty often results from nonlinearity.Using Abaqus Standard/Explicit,nonlinear
This paper analyzes the relationship between suspension and steering systems and wheels,and proposes the vehicle dynamics modeling method.Combined with suspension K&C and handling test of a concrete c
2016-2020 fuel economy regulation in China includes the off-cycle credit which is max.0.5L/100km for single vehicle model and requires the off-cycle benefit must be demonstrated with "measurable" prin
Based on the history of multi-step stamping,an advanced analysis method is proposed to analyze the structural properties of metal part.This method combines multi-step stamping forming and structure an
Minimum quantity lubricant(MQL)now becomes a development direction of mechanical manufacturing technology,for its advantages in environmental protection,cost and occupational health.It introduces appl
Through analyzing reports of the complains and the test results collected from Hainan nearly 10 years,It could be found out that the area of the body where corrosion happens is more concentrated and t
A full-variable-valvetrain prototype named Dual UniValve System has been developed for a GDI engine with SI/HCCI dual combustion modes,improving the fuel economy and emission performance under some of