【摘 要】
：
A full-variable-valvetrain prototype named Dual UniValve System has been developed for a GDI engine with SI/HCCI dual combustion modes,improving the fuel economy and emission performance under some of
【机 构】
：
Tongji University Pierburg GmbH
论文部分内容阅读
A full-variable-valvetrain prototype named Dual UniValve System has been developed for a GDI engine with SI/HCCI dual combustion modes,improving the fuel economy and emission performance under some of part and low load conditions.Based on the dynamic performance test,reliability of Dual UniValve System has been qualified.In addition,under the NEDC condition,UniValve system can optimize the friction loss significantly.The switching response time between valvelifts of 0mm to 8mm is only 0.16s,which provides a fast response for transient conditions.Furthermore,in the engine test with Dual UniValve System,SI/HCCI combustion mode switching has been also achieved with a fast speed,which increased indicated efficiency by 10%and reduced NO emissions by 99%.
其他文献
为保证指标间的相对独立性,将灰色关联分析应用到评价指标体系的选择中,将指标选择原则作为确定评价基准的依据,在确定基准和准则值的基础上,通过计算各准则值序列与基准序列的灰色关联度来对各指标体系进行分析排序,以实例阐述了该方法的具体应用.研究表明,该方法能够从量化角度反映评价原则在指标选择过程中的作用,为最优评价体系的选择提供依据.
本文主要论述了在汽车门内饰板的设计开发过程中,根据由整车碰撞目标分解到车门内饰板上强度、刚度性能指标,对门内饰板上在侧面撞击过程中对应的乘员胸部和腹部碰撞区域进行优化,使其在侧面碰撞发生时上述区域能够发生必要的变形甚至破坏,并且在变形或破坏的过程中产生的反作用力从的峰值不大于一定限值以保护乘员,通过运用“静态挤压”及“动态冲撞”试验工具进行验证.通过具体车型的具体产品的实践,可以得出结论:合理布置
利用Carsim与MATLAB/Simulink联合仿真软件平台,建立了具有电动助力转向系统的整车动力学模型,设计了电动助力转向系统模型预测控制策略.仿真结果表明,所设计的控制策略的驾驶人在获得较好的助力轻便性及转向路感,保证了转向系统稳定性及车辆操纵稳定特性.
本文通过以某车型排气系统管路断裂问题为研究案例,分别从断裂管路的材质、焊接质量、管路减薄量、装配尺寸、三维模型、发动机振动分析、振动对比试验、全寿命损伤等方面进行分析,确定断裂问题根本原因为发动机传递给排气系统的振动激励过大造成,确定通过对排气系统的补偿器进行优化的方法作为此类管路断裂问题的最终解决措施,并经过耐久可靠性路试验证了解决措施的可行性.
Dynamic simulation of vehicle model in time domain with nonlinearity draws more and more attention in the world.The difficulty often results from nonlinearity.Using Abaqus Standard/Explicit,nonlinear
This paper analyzes the relationship between suspension and steering systems and wheels,and proposes the vehicle dynamics modeling method.Combined with suspension K&C and handling test of a concrete c
2016-2020 fuel economy regulation in China includes the off-cycle credit which is max.0.5L/100km for single vehicle model and requires the off-cycle benefit must be demonstrated with "measurable" prin
Based on the history of multi-step stamping,an advanced analysis method is proposed to analyze the structural properties of metal part.This method combines multi-step stamping forming and structure an
Minimum quantity lubricant(MQL)now becomes a development direction of mechanical manufacturing technology,for its advantages in environmental protection,cost and occupational health.It introduces appl
Through analyzing reports of the complains and the test results collected from Hainan nearly 10 years,It could be found out that the area of the body where corrosion happens is more concentrated and t