• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. The fracture patterns of a Zr-based metallic glass and its Ta particle reinforced composite at a wid

The fracture patterns of a Zr-based metallic glass and its Ta particle reinforced composite at a wid

来源 :2nd International Conference on Lmpact Loading of Structural | 被引量 : 0次 | 上传用户：lyt7913
【摘 要】
：
　　Unixial quasi-static and dynamic compression experiments are conducted on bulk metallic glass(BMG: Zr55Cu30Ni5Al10)and its Ta particle reinforced composite(
【作 者】
：
W.X.Lu W.R.Jian X.C.Tang X.H.Yao 
【机 构】
：
DepartmentofEngineeringMechanics,SouthChinaUniversityofTechnology,Guangzhou,Guangdong510640,People'
【出 处】
：
2nd International Conference on Lmpact Loading of Structural
【发表日期】
：
2018年5期
【关键词】
：
Bulk Metallic Glass Composites Strain Rate Fracture Behavior SEM Characterizatio 
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　Unixial quasi-static and dynamic compression experiments are conducted on bulk metallic glass(BMG: Zr55Cu30Ni5Al10)and its Ta particle reinforced composite(MGMC:(Zr70Cu20Ni10)82Ta8Al10)at a range of strain rates across from 10-4 to 103 s-1 via Instron test machine and split Hopkinson pressure bar(SHPB),respectively.
其他文献
Empirical Formula for Estimating Spall Strength of Steel Fiber Reinforced Concrete under One-Dimensi
　　Steel fibers can significantly improve the ability of concretes to prevent spallation fracture,and a number of research has been carried out on the performa
会议
empirical formulaHopkinson barsteel fiber reinforced concretes (SFRC)spall st
Simulation and Evaluation of Damage Effect of Ring Damage Unit to Kinetic Energy Interceptor
　　In this article,we study the damage effect of ring damage unit-kinetic energy ring-on kinetic energy interceptor.Through the vulnerability analysis of the k
会议
Ring damage unitKinetic energy interceptorPenetrationSimulation
Numerical investigation of rock failure under ultra-high loading rate through a lattice spring model
　　In this work,the dynamic failure of rock under ultra-high loading rate is studied through a detailed numerical investigation of the gas gun experimental dat
会议
Ultra-high loading rateRockDistinct Lattice Spring ModelRate dependentDynami
Structural cell assembly model for impact on anisotropic foam
　　Solid foams possess a cellular microstructure,and are widely used in impact mitigation,energy absorption,cushioning and noise reduction applications.From ob
会议
Polyurethane foamCell assembly modelAnisotropyRate dependenceDeformation mec
Temperature Rise during Adiabatic Shear Localization of Pure Titanium
　　Adiabatic shear localization(ASL)is one of the failure mechanisms those are commonly observed within ductile materials under dynamic loading.ASL process is
会议
Adiabatic ShearASBTitaniumTemperature RiseHigh Speed PhotographyShear Compr
Ductile Failure of Advanced High Strength Steel at High Temperatures and High Strain Rates
　　Plasticity and fracture experiments are performed under extreme loading conditions on flat specimens extracted from DP800 and DP980 steel sheets.High strain
会议
Experimental analysis about the transverse inertia effect in the impact response of extra soft gelat
　　In this research,the transverse inertia effect in the dynamic response of extra soft gelatin-based material under impact loading is investigated.Previous th
会议
Gelatin-based materialInertia effectDynamic non-equilibriumImpact testsDigit
Influence of size on the toughness of elastic-brittle isotropic lattices
　　The mechanical properties of stochastic foams suffer from size-dependent effects so that test specimens must be `sufficiently large if representative bulk v
会议
LatticesSize effectsToughnessFinite element analysis
Dynamic split tensile properties of rubber concrete
　　Static and dynamic split tensile tests were conducted on rubber concrete with varied volume fractions of rubber particles that replaced fine aggregate(10%,2
会议
Rubber concreteDynamic split tensile test
Experimental investigation into the high strain rate fracture of AA7075-T6 sheet metal alloy
　　High strength aluminum alloys are currently of great interest in the automotive industry due to their superior strength-to-weight ratio.During the event of
会议
Strain rateFractureStress-stateAA7075-T6