【摘 要】
：
Molybdenum oxides,mainly including MoO3 and MoO2.are attractive materials with potentialapplications in catalysis,sensors and energy storage.Owing to the good electronic conductivity,highstability and
【机 构】
：
School of Materials Science and Engineering,Key Laboratory of Advanced Energy Storage Materials of G
论文部分内容阅读
Molybdenum oxides,mainly including MoO3 and MoO2.are attractive materials with potentialapplications in catalysis,sensors and energy storage.Owing to the good electronic conductivity,highstability and density,MoO2 was proposed as a host material for lithium ions.However,the application of MoO7 as anode material for lithium ion batteries was limited in the early research.due to the low capacityand poor cycling stability resulting from the bulky dimensions.the consequential slow kinetics and hugevolume changes during the charge/discharge process.To improve the performance of MoO2.a mostpromising way is to design and construct nanostructured composites[1-3].
其他文献
This paper presents the development of a highly efficient method for analyzing load distributions in multi-bolted composite joint using 2D-FE model.In the model, the bolt was modeledby using a fastene
In this paper, the research on structure buckling performance due to stiffeners on the composite domed rear pressure bulkhead of civil aircraft is finished.According to establish two categories struct
Composite stiffened panels is easy to lose stability on the compression loading, the composite stiffened component is very important for loading transfer as the key components of composite stiffened p
Residual stresses in friction stir welded (FSWed) particle reinforced metal matrix composites (PRMMC) affect the dimensions, the shapes and the performances of the FSWed joints significantly.However,
以微米级铝粉、膨胀石墨、二茂铁为原料,通过高温固相法制备不同铝含量的铁掺杂的铝/碳复合材料,其中铝的含量分别为28％,47％,50％.采用X射线衍射(XRD)、扫描电子显微镜(SEM)对铁掺杂的铝/碳复合材料的物相和形貌进行表征.同时,将样品制备成电极并组装成锂离子电池,并对电池进行循环性能测试、循环伏安和交流阻抗等测试来检测样品的电化学性能.以上测试结果表明,当铝的包覆量为47％时,超薄的膨胀石
能源问题是当今社会可持续发展的关键.二次电化学储能系统是提高能源利用效率的重要途径.锂离子电池具有高能量密度、高工作电压、循环寿命长等优势,在电子产品、电动汽车等众多市场有广泛的需求和应用前景.同时,轻、薄、可穿戴、柔性电子器件等概念的提出极大地拓宽了未来电子产品市场的需求,也对传统便携式储能系统提出新的挑战.目前锂离子电池具有成熟的技术基础,若能在此之上实现锂离子电池构造由刚性到柔性的转化,将极
负极材料是锂离子电池的重要组成部分.传统的负极材料是石墨,但其容量较低(372mAh g-1).硅是研究最多的负极材料之一,其优点是在地壳内储量丰富,环境友好,容量高(4200 mAh g-1).缺点是循环过程中有较大的体积变化(＞300 ％),造成粉化,在硅的表面形成不稳定的SEI膜,导致容量衰减[1].因此,新材料的开发和研究成为了人们关注的焦点问题.锰元素成本较低、储量丰富,作为锂离子电池具
锂离子电池由于具有安全使用寿命高、便捷可携带的特点,使其作为一种便携式新兴能源在众多电子产品领域得到了广泛的应用.尖晶石型Li4Ti5O12作为锂离子电池负极材料表现出极为优异的电化学性能.Li4Ti5O12在充放电过程中有一条平坦且相对较高的嵌锂电位1.55 V(vs.Li/Li+),避免了固体电解质界面(SEI)膜及锂枝晶的出现.另外,Li4Ti5O12由于在充放电过程中体积变化几乎可以忽略,
[Introduction] Carbon nanotubes(CNTs) with one-dimensional(1D) geometry and high aspectratio have been considered as an ideal conductive additive due to their high electronic and thermalconductivity a
随着锂离子电池产业的发展,研制性能更为优异的电极材料显得尤为重要.由于来源广泛、安全无毒和电化学性能优异,二氧化钛成为近些年锂离子电池负极材料的研究热点之一[1].另外,分等级结构因具有高孔隙率、大比表面积和能缓解充放电过程中的应力等优点,能有效地提高材料的嵌锂性能[2].