FORMABILITY相关论文
在不同焊接参数下对QP1180高强钢薄板进行激光焊接试验,对接头的显微组织、显微硬度、拉伸性能及杯突成形性能进行了分析。研究结......
采用光纤激光器焊接了0.1C-5Mn钢，研究了不同热输入对接头的组织、硬度、拉伸和成形性能的影响。结果表明，不同热输入的接头焊缝区均......
利用IPG YLS-6000光纤激光器对厚度为1.6 mm的QP1180高强钢进行激光焊接,研究了不同热输入(14~36 J/mm)对激光焊接接头组织及性能......
利用脉冲固体激光器对厚度1mm车用冷轧退火态双相钢DP590进行了激光焊接实验,研究了脉冲激光功率(45~130 W)对焊接接头的宏观形貌(......
This paper focused on the effect of pre-strain on forming limit curves (FLC) of 5754-O aluminum alloy sheet through util......
Analysis of edge microstructural characteristics and stamping formability of low carbon pickled stee
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
Tensile Properties with or without Heat Dispersion of Automotive Needlepunched Carpets Made up of Tw
Tensile properties of automotive needlepunched carpets made up of two layers of different materials (a fabric layer and ......
The effects of impurity element of Fe and microelements of Zn, Cr and Ti on the constituents,dispersoids, grain size, me......
Textural Evolution of AZ31B Magnesium Alloy Sheets Undergoing Repeated Unidirectional Bending at Roo
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using se
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
Effect of Ni addition on microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys with a hi
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
Investigation of the mechanical performance of Al-coated DI steel sheets prepared by DC magnetron sp
...
The ANSYS simulation software was used to analyze the bending formability of laminate steel/resin/steel lightweight comp......
The forming limit diagrams(FLD)of AZ31B magnesium alloy sheet were tested by means of the electro etching grid method ba......
An annealed TC4 titanium alloy sheet was treated by high density electropulsing (Jmax=(5.09-5.26)×103A/mm2, tp=110 μs)......
Textural Evolution of AZ31B Magnesium Alloy Sheets Undergoing Repeated Unidirectional Bending at Roo
In this paper, repeated unidirectional bending (RUB), was applied to improve the texture of AZ31B magnesium alloy sheets......
Sand casting and die casting processes have been used widely for complex automotive products such as knuckle,arm,etc.Usu......
The phase evolution and magnetic properties of Nd9 -xYxFe72Ti2Zr2B15 (x = 0, 0.5, 1, and 2) melt-spun nanocomposite ribb......
研究AA5052/聚乙烯/AA5052复合层板成形过程中表层面板与中心聚合物层界面黏接强度对其成形性的影响规律.考虑复合层板界面特性,建......
In order to investigate the influence of hydrostatic pressure on compression limit of the ring, numerical simulation and......
