分工协作 坚持回收报废汽车的规定 利用好解体的废物料

来源 :金属回收 | 被引量 : 0次 | 上传用户:ZY5158598
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
一、领导重视,分工明确是抓好报废汽车回收工作的关健。接收报废汽车,对我们来讲是一项新的工作,我公司在八一年初,只回收报废汽车十余部,回收的汽车破烂不堪。很不完整,只有五大总承件的主要零件。自接到国务院国发(81)173号文件国家物资局(82)物回字210号文件,公司领导向地区行署主要领导同志汇报了全区当前报废汽车回收工作情况和存在问题。明确由地区计委负责抓这项工作。地区计委主持召开了关于更新报废汽车回收工作会议,地区交通局、车管办、车辆 First, the leadership attaches great importance to the division of labor is a clear grasp of the work of scrapped car recycling key. Receiving scrapped cars is a new job for us. At the beginning of 1981, our company only retired more than ten scrapped cars and the cars they collected were dilapidated. Very incomplete, only the five major components of the main parts. Since the State Development and Reform Commission (No. 81) Document No.173 issued by National Materials Administration Bureau (No. 82) Document No. 210, the leaders of the company reported to the chief leaders of the regional administrative department about the current situation and existing problems of the recycling of scrapped vehicles in the region. Clearly by the Planning Commission is responsible for this task. Regional Planning Commission presided over the meeting on updating scrap car recycling work, the Regional Transport Bureau, Che Kwun Ban, vehicles
其他文献
阿尔金断裂是青藏高原西北边缘最主要的断裂.天然地震P波层析成像结果揭示了阿尔金断裂(严格地说这里指阿尔金断裂中部,下同)为一条宽约40km左右的低速带,并以比较直立的产状向下
选取了TGS晶体的 (0 0 1) ,(110 ) ,(0 10 )和 (10 0 )四个面为研究对象 ,分析讨论了TGS晶体的表面扩散螺位错生长机制 ,发现生长基元的脱水化进入表面层过程与表面扩散过程
杭州市第一汽车运输公司最近研制成一种既能吊运,又能叉运,叉吊结合的一机多能的件装装卸机械——汽车运行吊。并已于去年十二月通过技术鉴定(照片见封二)。汽车运行吊是在
On December 14th,2007 Zhejiang Hengyi Group commenced construction for the200 000 t/a caprolactam (CPL)project.With a total investment of around RMB4.0 billion
期刊
三二○厂为了治理空气压缩机站严重的噪音污染,进行了长时间的消音研究,研制成两室串接式抗性扩张室消音装置。经一年多使用证明,消音效果很佳,完全达到了预定的技术指标。
1970年9月建造时的骨架1974年8月第一次鉴定时的骨架1978年5月底盘大修时的骨架1979年8月第二次鉴定时的骨架1974年8月第一次鉴定时的骨架 1979年8月第二次鉴定时的。骨架全
期刊
<正>~~
期刊
用常规页岩回收率方法探讨了聚乙二醇的页岩抑制作用,并用磷钼酸沉淀法测定了聚乙二醇(M=10000)在新疆土上的吸附量。实验表明,单一聚乙二醇在水中无抑制作用,在1mol/L NaCl
【正】 The first phase of the 160 000 t/a plastic profile project funded by Dalian Shide Group with an investment of RMB1.6 billion started production in Luohe,