论文部分内容阅读
60% white corundum used for aggregate,5% aluminium powder for fixed additions and 35% various additives for matrix were prepared for specimens 1#,2#,3#.They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press,then dried at 200 ℃ for 24 h.Effects of various additives on 1500 ℃×2 h creep properties of Al3CON reinforced corundum composite were researched.The experimenal results show that creep coeffi-cients of specimens 1#,2#,3# at 1500 ℃×2 h are 1.4×10-4,-9.4×10-4,-22.6×10-4,respectively.Crushing strength of the slide plate added with suitable additive A after fired at 1500 ℃×3 h reaches to 225 MPa,the creep rate is positive all the time from 0% to 0.014% at 1500 ℃ for 2 h.The micro-structure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1#,and the strength of the composite is increased.The hot modulus of rupture is up to 59 MPa at 1400 ℃ and the RUL is obvi-ously higher than that at 1700 ℃.Its service life is two times as that of Al2O3?C slide plate when used in the process of pouring steel.The mechanism of creep rate resistance of the composites can be dis-covered by means of SEM and EDAX analysis.It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas,C,Al and Al2O3 inside the matrix of the composites during in-situ reaction,which gives the composites outstanding creep rate resistance for the dense zone re-sulting from Al3CON oxidation that inhibits contraction at the high temperature.Besides,the matrix will turn into the multiphase with high refractoriness,N content and its Al3CON reinforced fiber will further increase accordingly.In addition,Al3CON formed by Al2O3 and C,Al in the matrix with N2 in gas will inhibit the creep rate and also greatly improve the creep rate resistance of the composites.
60% white corundum used for aggregate, 5% aluminum powder for fixed additions and 35% various additives for matrix were prepared for specimens 1 #, 2 #, 3 # .They were mixed uniformly with the suitable resin as a binder and pressed under pressure of 315 ton forging press, then dried at 200 ° C. for 24 h. Effects of various additives on 1500 ° C. × 2 h creep properties of Al3CON reinforced corundum composite were researched. The experimenal results show that creep coeffi-cients of specimens 1 #, 2 #, 3 # at 1500 ° C × 2 h are 1.4 × 10 -4, -9.4 × 10 -4, -22.6 × 10 -4, respectively.Crushing strength of the slide plate added with suitable additive A after fired at 1500 ° C × 3 h reaches to 225 MPa, the creep rate is positive all the time from 0% to 0.014% at 1500 ° C for 2 h. The micro-structure result analysis shows that reinforced phases of Al3CON fiber composite have been formed after fired with Al powder in coke at high temperatures for specimen 1 #, and the strength of the composite is increased. The hot modulus of r upture is up to 59 MPa at 1400 ° C and the RUL is obvi-ously higher than that at 1700 ° C .Its service life is two times as that of Al2O3? C slide plate when used in the process of pouring steel. The mechanism of creep rate resistance of the composites can be dis-covered by means of SEM and EDAX analysis. It is concluded that the active Al3CON and Al2O3 multiphases that were formed by N2 in gas, C, Al and Al2O3 inside the matrix of the composites during in- situ reaction, which gives the composites outstanding creep rate resistance for the dense zone re-sulting from Al3CON oxidation that inhibits contraction at the high temperature.Besides, the matrix will turn into the multiphase with high refractoriness, N content and its Al3CON reinforced fiber will Al3CON formed by Al2O3 and C, Al in the matrix with N2 in gas will inhibit the creep rate and also significantly improve the creep rate resistance of the composites.