【摘 要】
：
Different components of deep-sea submersibles,such as the pressure hull,are usually subjected to inter-mittent loading,dwell loading,and unloading during servic
【机 构】
：
State Key Laboratory of Nonlinear Mechanics,Institute of Mechanics,Chinese Academy of Sciences,Beiji
论文部分内容阅读
Different components of deep-sea submersibles,such as the pressure hull,are usually subjected to inter-mittent loading,dwell loading,and unloading during service.Therefore,for the design and reliability assessment of structural parts under dwell fatigue loading,understanding the effects of intermittent loading time on dwell fatigue behavior of the alloys is essential.In this study,the effects of the inter-mittent loading time and stress ratio on dwell fatigue behavior of the titanium alloy Ti-6Al-4V ELI were investigated.Results suggest that the dwell fatigue failure modes of Ti-6Al-4V ELI can be classified into three types,i.e.,fatigue failure mode,ductile failure mode,and mixed failure mode.The intermittent loading time does not affect the dwell fatigue behavior,whereas the stress ratio significantly affects the dwell fatigue life and dwell fatigue mechanism.The dwell fatigue life increases with an increase in the stress ratio for the same maximum stress,and specimens with a negative stress ratio tend to undergo ductile failure.The mechanism of dwell fatigue of titanium alloys is attribute to an increase in the plastic strain caused by the part of the dwell loading,thereby resulting in an increase in the actual stress of the specimens during the subsequent loading cycles and aiding the growth of the formed crack or damage,along with the local plastic strain or damage induced by the part of the fatigue load promoting the cumu-lative plastic strain during the dwell fatigue process.The interaction between dwell loading and fatigue loading accelerates specimen failure,in contrast to the case for individual creep or fatigue loading alone.The dwell fatigue life and cumulative maximum strain during the first loading cycle could be correlated by a linear relationship on the log-log scale.This relationship can be used to evaluate the dwell fatigue life of Ti alloys with the maximum stress dwell.
其他文献
The novel idea of alloying,which is based on the utilization of multiple principal elements in high concen-trations,has created a novel class of promising mater
试验在1台由高压共轨柴油机改装的甲醇-柴油双燃料发动机上展开,通过仪器模拟不同海拔,进而研究在高原环境下甲醇-柴油双燃料(DMDF)燃烧的循环波动。试验主要在1800 r/min下,通过调整发动机负荷、甲醇替代率和柴油喷射参数,研究各种参数在不同海拔下对发动机燃烧稳定性的影响。缸内压力参数,如峰值压力(pmax)和平均指示压力(IMEP),被用来量化双燃料发动机循环波动。研究结果表明,DMDF燃烧在高原下的循环波动表现出与平原上相似的趋势;随海拔升高,峰值压力循环波动系数(COV_(
采用集中质量法建立了某V12柴油机扭振动力学模型,计算得到了800~2500 r/min转速范围内的进排气左右凸轮轴负载扭矩激励,对凸轮轴进行了强迫振动仿真,获取凸轮轴各谐次扭转振幅和滚振谐次,并分析计算凸轮轴滚振振幅。结果表明:第4.5,5.0,5.5及6.5谐次主要贡献凸轮轴强迫扭振振幅,在2500 r/min转速区域时凸轮轴扭振振幅峰值均达到最大值,3谐次的激励力矩是构成滚振的主要成分。分析并获取试验柴油机凸轮轴滚振最佳简谐系数,采用多次近似拟合低转速下的振幅结果以消除滚振误差的方法,建立了凸轮轴滚
为提高四分之一波长微带线雷电保护器的带宽,降低输出残压,提出了分节微带线与串联电感的组合匹配设计方法.仿真分析了四分之一波长微带线避雷器的不足,通过对分节微带线、串联电感的仿真优化,拓展了雷电保护电路的带宽,仿真结果表明防护电路在1 GHz到3 GHz内具有良好的电压驻波比即宽带特性.利用电压梯度法实现器件间的组合匹配,防护电路实测结果表明,在注入组合波波形为1.2/50μs&8/20μs,电压峰值为10 kV的雷电磁脉冲下,输出残压为79 V.通过组合匹配方法设计的防护电路具有频带宽、残压低、易
文中利用抛物方程(parabolic equation,PE)方法,从纵向剖面和区域覆盖两个维度,对3.6 GHz频点在都市、郊区、乡村三种典型场景下的传播特性进行分析,并将仿真结果与ITU-R P.1546方法仿真结果进行对比分析.分析结果表明:PE方法能够描述信号传输直射、绕射、反射波束,与各场景传播特点相匹配,具有较好的适用性;PE方法与ITU-R P.1546方法变化趋势有着较好的一致性;PE方法结合地形的不规则变化,覆盖仿真结果更为细致,体现出“确定性预测”的优势.本文研究成果可为5G毫米波典型
石墨烯由于其独特的层状结构与滑移特性,可以加入润滑油中作为固体润滑添加剂来改善润滑性能,满足不断强化的柴油机对高性能润滑油的需求。通过液相等离子方法制备了1 nm左右的石墨烯薄片,并运用超声振荡分散法以质量分数0.05%加入RP-4652D润滑油中,采用往复式活塞环-气缸套摩擦磨损试验机,研究了温度对石墨烯润滑油添加剂摩擦磨损性能的影响规律。结果表明:当试验温度为150℃,180℃,210℃时,加入石墨烯润滑油的摩擦系数比未加入石墨烯润滑油时分别降低了10.8%,6.1%,8.8%,气缸套磨损量分别降低了
地基承载力概念和与之相随的允许应力法已在我国被强制推行近20年,即将实施的《建筑和市政地基基础通用规范》继续推行。本文对此进行分析,认为:地基承载力特征值应改成地基承载力许用值,其定义应改为具有一定安全储备的地基承载能力代表值;地基承载力验算应采用总安全系数法,在地基承载力方面应采用地基极限承载力标准值。
根据国六柴油机台架上的性能试验经验,某些后处理系统SCR下游NO_x传感器测量的NO_x值与台架气体分析仪的测量值之间存在较大偏差。利用计算流体力学(CFD)技术对两种后处理方案进行计算,分析了尿素喷雾的形态及蒸发分解,对SCR载体前端面和NO_x传感器安装位置的氨分布均匀性进行了评估,针对NO_x传感器探头位置的氨分布偏差值占比进行了分析。仿真结果表明,SCR前氨气不均匀是NO_x传感器测量偏差
连体结构往往因独特的建筑造型成为城市地标建筑,CCTV主楼、重庆来福士广场、苏州东方之门、武汉保利广场等都是典型的连体建筑。而每个连体结构受其连接方式和位置、塔楼动力特性及抗震设防烈度等因素影响,均有其自身的抗震设计思路。该文以某连体结构为例,对以下几个方面进行分析:(1)连接体连接方式的选择及影响因素;(2)基于振型模态的动力特性分析;(3)连体结构在X、Y方向的受力机制;(4)连接体性能水准的选择及构件设计;(5)通过非线性时程反应分析手段,识别连接体各杆件在罕遇水准的性能。结果发现:(1)连体结构连