【摘 要】
：
Streams and rivers,particularly smaller ones,often do not maintain steady flow rates for long enough to reach equilibrium conditions for sediment transport and bed topography.In particular,streams in small watersheds may be subject to rapidly changing hyd
【机 构】
：
United States Department of Agriculture,Agricultural Research Service,National Sedimentation Laborat
论文部分内容阅读
Streams and rivers,particularly smaller ones,often do not maintain steady flow rates for long enough to reach equilibrium conditions for sediment transport and bed topography.In particular,streams in small watersheds may be subject to rapidly changing hydrographs,and relict bedforms from previous high flows can cause further disequilibrium that complicates the prediction of sediment transport rates.In order to advance the understanding of how bedforms respond to rapid changes in flow rate,a series of flume experiments were performed where the flow was reduced rapidly from equilibrium conditions.Sediment transport rates and bed elevation data across the flume and over a 15-meter-long test section were collected during the experiments to allow detailed examination of evolving bedform dynamics.It was found that relict bedforms stopped moving completely after flow reductions,and the mode of sediment transport was shifted to small bedforms that arose rapidly over dune stoss sections throughout the test section.The changes in sediment transport with time as the sand bed adjusted to the new flow rate was found to agree with predictions based on the relations proposed in Wren et al.(2020).Wavelet analysis is used to visualize changes in length and amplitude scales during the bed transition process.
其他文献
为提升极坐标法测量渐开线齿廓偏差的精度,研究了坐标系建立误差补偿,构建了极坐标法测量齿廓偏差的测量模型和坐标系建立误差补偿模型.以ISO 0级精度齿轮为例,借助齿轮测量中心的数字孪生体和物理平台进行了仿真和实验研究,分析了坐标系建立误差对齿廓偏差的影响,并对齿廓偏差进行误差补偿.研究表明,坐标系建立误差对极坐标法测量齿廓形状偏差的影响可忽略不计,对齿廓总偏差和齿廓斜率偏差均有显著影响;坐标系建立误差补偿的方向对齿廓偏差有不同影响,其中X方向的坐标系建立误差对其影响最显著;提出的误差补偿方法可使齿廓偏差达到
为了降低铣削弹性变形对叶轮叶片加工精度的影响,在获得五轴刀路轨迹和铣削力的基础上,通过ABAQUS软件二次开发有限元仿真和“单元生死”技术,对刀具移动过程中的铣削力加载和材料去除进行模拟,完成了叶片五轴铣削变形预测模型的构建.仿真结果表明,迭代补偿后叶片的平均变形误差和最大变形误差分别减小了92.93％和92.64％.
The mechanism of bridge pier scour becomes more complex in the presence of debris accumulation upstream of the pier.While using countermeasures may be effective in reducing scour,their efficacy could be undermined in such a situation.The current study inv
A turbidity current is a turbulent,particle-laden gravity current that is driven by density differences resulting from the presence of suspended sediment particles.The current travels downslope,bearing a large amount of sediment over a great distance,and
基于固有应变理论,使用Weld Planner有限元软件对等高齿弧锥齿轮铣刀盘的焊接变形进行研究,通过建立有限元模型准确快速得到铣刀盘的焊接变形规律.根据仿真模型和焊接参数对铣刀盘进行焊接,测量的变形和数值与仿真参数一致.
Little is known about the distribution and risk levels of nutrients and organic matter (OM) in the surface sediment of shallow submerged macrophyte-dominated lakes.In the current study,sixty surface sedi-ment samples were collected from Xukou Bay,a typica
A velocity formula is proposed for flow over a mobile sediment bed induced by velocity-skewed waves and current.The formula is obtained by a separation of waves and current velocities and requires seven free variables related to free stream velocity and s
砂带磨削过程中,磨粒的磨损会影响材料去除率以及零件表面质量.针对砂带磨削过程中刀具状态预测问题,采用基于支持向量机和遗传算法的预测模型实现砂带磨损状态的有效预测,并对预测效果进行仿真验证.简化砂带磨削工艺,构造磨削工艺数学模型.引入K值最近邻算法作为遗传算法的适应度函数,构造了基于支持向量机和遗传算法的预测模型.采用MATLAB数学软件对砂带进行实时仿真计算,并与采集的实验数据进行对比和分析.结果 显示,基于支持向量机和遗传算法的预测模型,预测的不同加工参数下的砂带磨损量与实验数据基本吻合,误差不超过8％
根据矿山贫化率、损失率指标的定义、计算方法,分析矿山贫损产生的原因.结合矿山三维建模技术,提出贫损指标计算的关键参数的获取途径,即从空区探测技术(CMS)出发,对矿山贫损指标的计算与管理进行探讨,从而有效解决矿山贫损指标难以监测的难题.
Reliable modeling of river sediments transport is important as it is a defining factor of the economic viability of dams,the durability of hydroelectric-equipment,river susceptibility to pollution,suitability for navigation,and potential for aesthetics an