【摘 要】
：
Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully and uniformly mixing the two componen
【机 构】
：
School of Materials Science and Engineering, Wuhan University of Technology, Wuhan 430070, China;Rai
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully and uniformly mixing the two components. The research was carried out through the combination of experimental test and finite element simulation. The experimental results show that when the pore density is constant, the size of the bubble hole is an important factor affecting the mechanical properties of the model. The smaller the size of the bubble hole, the less likely it is to produce stress concentration inside the model, and the stronger the resistance to material deformation. Under the random distribution, the lower the density of the polyurethane cured material, the higher the probability of damage between the adjacent bubbles, which is not conducive to the stability of the material. The density of the cured material should not be lower than 199 kg/m3.
其他文献
Composite nanofiber membranes based on biodegradable poly(lactic acid) (PLA) and cellulose nanofibrils (CNF) were produced via electrospinning.The influence of CNF content on the morphology,thermal properties,and mechanical properties of PLA/CNF composite
The failure patterns and energy evolution of three types of shaft lining concrete subjected to static and dynamic loading were reported. The energy and damage characteristics of concrete were determined by means of a uniaxial hydraulic servo machine, acou
By using NaOH and Na2SiO3 as the activator, the mechanical properties and shrinkage of the geopolymer after incorporation of 0％, 10％, 20％, and 30％ epoxy resin were investigated. The mechanism of epoxy resin toughening metakaolin based geopolymer was analy
To promote the photocatalytic performance TiO2 and enlarge its application in visible region, carbon doped TiO2 (C/TiO2) composites were synthesized by wet impregnation method using sucrose as a precursor and used for phenol photocatalytic reaction. The s
Polyethyleneimine (PEI) functionalized Fe3O4 MNPs were synthesized by a modified hypothermal oxidative hydrolysis method.The magnetic nanoparticles showed positively charged surface,strong magnetic responsivity and uniform particle size distribution at 56
Three CrN coatings were deposited on the Inconel X750 through the metal vapor vacuum arc ion implantation and the magnetic filtered cathodic vacuum arc deposition system (MEVVA-FCVA) with the N2 flow rates of 10,50,and 100 sccm,respectively.The surface mo
To investigate the transport characteristics of chloride ions in cement-based materials, the Mori-Tanaka (M-T) prediction scheme of the effective diffusion coefficient in composites containing single-phase and multi-phase inclusions is systematically dedu
Transparent hydroxyapatite (HAp) ceramics with the grain size ranging 86-1 300 nm were successfully synthesized by spark plasma sintering (SPS) at 925-1 200 ℃.All the sample achieved final density higher than 99.7％.The phase stability was identified by X-
To promote the stability and efficiency, quadruple-cation perovskite system (blending of MA, FA, Cs, I, Br, etc) was introduced to substitute the traditional MAPbI3 perovskite. Perovskite films degraded by water can be recovered by a simple method. The Pb
The present study aimed to improve the pervaporation (PV) performances of polydimethy-lsiloxane (PDMS) membranes by using special cross-linkers. The γ-methacryloxypropyl trimethoxy silane (KH-570) cross-linked PDMS membranes were fabricated and characteri