【摘 要】
：
To investigate the osteoinductive and ectopicly osteogenic effects of a novel peptide P24 derived from bone morphogenetic protein 2 (BMP2), biodegradable collag
【机 构】
：
Department of Orthopaedics,Institute of Polymer Science
论文部分内容阅读
To investigate the osteoinductive and ectopicly osteogenic effects of a novel peptide P24 derived from bone morphogenetic protein 2 (BMP2), biodegradable collagen scaffolds (CS) were used to load BMP-2-derived peptide solutions with different concentrations (0.4 mg peptide/CS, 0.1 mg peptide/CS and pure CS, respectively), and the implants were implanted into muscular pockets on the back of Wistar rats.Radiographs and histological analysis were performed to evaluate the ectopic bone effects. Active ectopic bone formation was seen in both groups containing the peptide at different concentration (0.4 mg and 0.1 mg),whereas no bone formation and only fibrous tissue was seen in the pure CS group. The new bone formation induced by the peptide P24 displayed a dose-dependent and time-dependent efficiency. The new bone formation in the 0.4 mg peptide/CS group significantly increased than that of the 0.1 mg peptide/CS group. This novel BMP-2-derived peptide had excellent osteoinductive and ectopicly osteogenic properties which were similar to those of BMP2.
其他文献
目的 探讨急性颅脑损伤患者心肌酶谱变化对病情严重程度的影响.方法 对80例急性颅脑损伤患者(观察组)和同期60例健康体检者(对照组)的静脉血清AST、LDH、CK、α-HBDH、CK-MB
以络合型TiCl3催化剂、N型Ziegler-Natta催化剂和[O,O,N,N]茂金属为主催化剂,采用本体聚合方法,制备了单峰和双峰聚α-烯烃油品减阻剂,考察了催化剂的种类与用量对聚α-烯烃
针对目前机电液一体化模型建立后,模型中参数难以快速准确标定的问题,把响应面思想应用于中型挖掘机这一类机电液一体化模型参数标定。采用键合图理论建立挖掘机动态数学模型
In the practical cold-spraying process,a number of particles impact onto a substrate and then form a coating.To study the deformation behavior and multi-particl
Porcine aortic valves were decellularized with trypsinase/EDTA and Triton-100. With the help of a coupling reagent Sulfo-LC-SPDP, the biological valve scaffolds
Carbon spheres with size of 50-300 nm were synthesized via a solvent-thermal reaction with calcium carbide and chloroform as reactants in a sealed autoclave. Th
采用包裹工艺和热压工艺制备了Al2O3/Ni金属陶瓷.在1450°C热压Ni包裹Al2O3复合粉体得到相对密度＞98%的金属陶瓷,当温度＞1400°C时,随着Ni含量的增加致密度下降.Ni颗粒位于三角
PDLLA/CHI/β-TCP/NGF composite films were prepared by a solvent evaporation method.The degradation characteristics of the poly (d, l-lactide) composite films we
The feasibility of employing non-ionic surfactant (Triton X-100) as an alternative and effective solvent for the microwave-assisted extraction of glycyrrhizic a
A novel method was used to fabricate AIN coating on graphite substrate. This approach included two steps: firstly, the emulsion composed of BN and anhydrous eth