【摘 要】
：
人字齿同步带传动因承载能力大、传动误差小、噪声低等特点备受关注。分析人字齿同步带和带轮齿廓曲线参数,利用高阶切触阶啮合理论建立带齿和轮齿齿廓方程。对人字齿同步带
【机 构】
：
齐齐哈尔大学机电工程学院,无锡贝尔特胶带有限公司,
论文部分内容阅读
人字齿同步带传动因承载能力大、传动误差小、噪声低等特点备受关注。分析人字齿同步带和带轮齿廓曲线参数,利用高阶切触阶啮合理论建立带齿和轮齿齿廓方程。对人字齿同步带模具齿廓曲面加工特性进行研究,并根据坐标变换和齿轮啮合原理推导人字齿同步带模具曲面方程。最后提出一种用于同时生产多根人字齿同步带的组合分拆式模具,并成功用于指导企业生产。
Herringbone teeth synchronous belt drive due to the carrying capacity, transmission error is small, low noise characteristics of much concern. The teeth tooth profile and pulley profile curve parameters are analyzed, and the tooth profile equation with teeth and gear teeth is established by using the theory of high-order tangent-order meshing. The research on the processing characteristics of tooth profile and curved surface of herringbone timing belt die is deduced. The equation of die surface of herringbone tooth timing belt is deduced according to the principle of coordinate transformation and gear meshing. Finally, a combined split mold for simultaneous production of a plurality of herringbone timing belts is proposed and used successfully to guide the production of an enterprise.
其他文献
采用试验研究与计算机工艺仿真相结合的方法,对圆柱齿轮闭式温锻成形过程中影响其成形效果的因素——模具结构进行研究,分析模具结构对齿轮成形的影响。结果表明,冲孔连皮设
A number of E-W trending subparallel mafic dikes of diabase composition occurred in Gyangze-Kangma area,eastern Tethyan Himalaya,southern Tibet.They intruded in
采用光学显微镜、扫描电镜及透射电镜等分析了C300焊缝金属焊态、焊后固溶态及焊后固溶时效态的微观组织变化、强韧性特征及断口裂纹扩展路径。结果表明,经过时效处理,在马氏
张惠辛:今天我们要讨论的主题是:影视广告如何寻找卖点。卖点有两个概念,一个是卖给消费者的卖点,还有一个是卖给广告主的卖点,这两者互相联系,不可分割。如果你能够找到打动
请下载后查看，本文暂不支持在线获取查看简介。
Please download to view, this article does not support online access to view profile.
请下载后查看，本文暂不支持在线获取查看简介。
Please download to view, this article does not support online access to view profile.
Occurrence of mafic dykes in Himalaya has been intriguing and debated since long because of its difficulty to ascent and emplacement through a thickened crust.M
请下载后查看，本文暂不支持在线获取查看简介。
Please download to view, this article does not support online access to view profile.
请下载后查看，本文暂不支持在线获取查看简介。
Please download to view, this article does not support online access to view profile.
这次参加我会习作展览[1],竟获得一等奖,真使我感愧莫名,首先应该感谢党和政府对于国画的领导和我会同志们经常对我的帮助。我想借此机会抛砖引玉,谈谈我的创作过程,以求得画