论文部分内容阅读
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生、测量监控等方面人手,介绍了S226海滨大桥主桥连续预应力混凝土变截面箱梁2#～7#块、8#、8
Microstructure, mechanical and corrosion behavior of high strength AA7075 aluminium alloy friction s
【摘 要】
：
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生、测量监控等方面人手,介绍了S226海滨大桥
【机 构】
：
Department of Mechanical Engineering, R.I.T., Visakhapatnam, India“,”Defence Metallurgical Research
【出 处】
：
城市道桥与防洪
【发表日期】
：
2015年4期
其他文献
The present work pertains to the study on joining of AA6061 and AISI 4340 through continuous drive friction welding. The welds were evaluated by metallographic
Pitting corrosion resistance and bond strength of stainless steel overlay by friction surfacing on h
Surface modification is essential for improving the service properties of components. Cladding is one of the most widely employed methods of surface modificatio
Effect of welding processes on mechanical and microstructural characteristics of high strength low a
Naval grade high strength low alloy(HSLA) steels can be easily welded by all types of fusion welding processes. However, fusion welding of these steels leads to
Natural fragmentation of warheads that detonates causes the casing of the warhead to split into various sized fragments through shear or radial fractures depend
Optimization of friction stir welding parameters for improved corrosion resistance of AA2219 aluminu
The aluminium alloy AA2219(Al—Cu—Mg alloy) is widely used in the fabrication of lightweight structures with high strength-to-weight ratio and good corrosion r
可信计算中,应用软件可信度量是信任链中重要的一环,由于现代软件规模过于复杂,要确保应用软件可信而不能仅仅依靠软件数据完整性度量。所以,在软件数据完整性的基础上,结合软件可靠性及可用性多个方面综合考虑可信因子的提取,为后续专家系统的分类识别提供可信量化依据,解决对未知软件可信程度进行预测的问题。
The effect of underwater shock wave on different target plates has been studied.An underwater shock wave generator(shock tube) was used to study the interaction
针对部队在军事物资管理上的突出问题,提出了基于RFID技术的军事物资管理系统。该系统以射频识别技术为依托,通过规范的编码规则及电子标签来唯一标识每个装备实体。在使用中,通过对电子标签的自动识别,动态、智能地管理与监控各类装备物资的使用情况。该系统有效地解决了传统管理模式中管理效率低下和管理粒度不细致等问题。
The present work discusses the experimental study on wire-cut electric discharge machining of hot-pressed boron carbide.The effects of machining parameters,such
Optimal trajectory and heat load analysis of different shape lifting reentry vehicles for medium ran
The objective of the paper is to compute the optimal burn-out conditions and control requirements that would result in maximum down-range/cross-range performanc