【摘 要】
：
In this study, we reported on the concept and practical use of cation exchange resin (CER) for removing anions in water via pretreating the CER with metal salts
【机 构】
：
Nanomaterial Laboratory,An Giang University,18 Ung Van Khiem St.,Dong Xuyen Dist,Long Xuyen City,An
论文部分内容阅读
In this study, we reported on the concept and practical use of cation exchange resin (CER) for removing anions in water via pretreating the CER with metal salts. The cation exchange resin-supported iron and magnesium oxides/hydroxides composite (Fe-Mg/CER) was synthesized and introduced as a new and potential adsorbent for selective removal of nitrate ion in the water environment. Characteristics of Fe-Mg/CER were determined by techniques such as Fourier-transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction. The results showed that Fe-Mg/CER material had a high nitrate adsorption capacity of 200 mg NO3-·g-1 with a fast equilibrium adsorption time of 30 min at pH 5. In addition, it had good durability of at least 10 times of regeneration, which could be applied to practical water and wastewater treatment.
其他文献
本文采用FAST软件对一种浅吃水单柱式浮式风机系统的动力学特性进行了研究。这一浮式风机适用于能源成本相对合理、水深为150 m的海域。本文首先讨论了这一浮式风机系统和OC3-Hywind系统在动力学特性方面的差异,然后研究了风尤其是湍流风对系统动力学特性的影响,最后对这一系统在多种载荷状况下的动力学行为进行了详尽的分析。研究结果表明:湍流风会在系统固有频率附近引起显著的激励;纵荡和纵摇运动取决于风轮推力,它们通过风轮推力和相对风速之间的联系建立起耦合关系;Spar平台的艏摇运动主要取决于平台横摇时由风轮推
In view of the practical importance of the heat transfer devices in various thermal engineering fields including chemical and nuclear engineering, this study ai
本文对码头系泊的FSRU和LNG船的水动力性能进行了研究,分别对FSRU单船码头和FSRU-LNGC并排码头系泊进行了模型试验。码头与船和船与船之间均采用系泊缆和靠垫进行连接。试验中考虑了风、流、浪等环境因素对码头系泊系统的影响。在风浪流模型试验中,分别测量了不同海况下系泊系统的动态响应,其中包括FSRU和LNG船的六自由度运动响应、系泊缆张力和靠垫接触力。相比较其它浪向,横浪(90°)引起的船舶运动更大,进而导致系泊缆和靠垫的受力增大。结果还表明,FSRU单船码头系泊在所有海况下安全性较好,但对于LNG
对6005A-T6铝合金挤压型材进行焊速为1000 mm/min的搅拌摩擦高焊速焊接,研究了对接面机械打磨对接头组织和力学性能的影响.结果 表明,与生产中常用的焊前打磨处理相比,尽管对
以合金表面粘砂比例和粗糙度为优化指标,采用多指标正交实验设计方法,通过极差分析研究了定向凝固用陶瓷型壳面层粒度配比和Cr2O3添加剂对铸件表面质量的影响.结果 表明,铸件
随着大型集装箱船的发展,针对斜浪条件下扭矩载荷特性及其结构强度的分析研究日益重要。本文采用选定的某大型集装箱船开展动态载荷(DLA)分析,建立了水动力湿表面计算模型和质量模型,研究基于扭矩传递函数和主要载荷控制参数的斜浪设计波参数确定方法,分析超越概率水平对扭矩载荷计算结果的影响。考虑典型斜浪参数和超越概率水平,分析对比DLA扭矩与船舶规范(ABS和HCSR)扭矩的差异及原因,提出集装箱船扭矩载荷计算与应用的建议。在此基础上,选定3个斜浪计算工况(45°,60°和75°)开展结构强度分析,通过分析应力计算
The aim of the study was to synthesize zinc oxide nanoparticles (ZnONPs) composite with clay by a novel route and then to explore the capability of composite of
使用Gleeble-1500D热模拟实验机对37CrS4特种钢进行单道次热压缩实验,研究了37CrS4钢在950～1100℃和0.01 s-1～10 s-1条件下的热压缩流变应力行为.结果 表明:这种钢的真应力应变
The high water content of sludge has always posed significant challenges for its treatment. Synthetic floc-culants, which are widely used in sewage treatment pl
从2009年到2017年,SUV在新车市场中的份额从不到8％一路增长至43％,年销量复合增长率超过40％,几乎所有车企都会将SUV作为主要的增长驱动力.而SUV本身的高溢价能力,也让越来越多的