【摘 要】
：
Hypereutectic Al-Si-Cu coatings were prepared by supersonic atmospheric plasma spraying to enhance the surface performance of lightweight alloys.To find out optimum process conditions and achieve desirable coatings,this work focuses on the influence of th
【机 构】
：
National Key Laboratory for Remanufacturing,Army Academy of Armored Forces,Beijing 100072,China;Nati
论文部分内容阅读
Hypereutectic Al-Si-Cu coatings were prepared by supersonic atmospheric plasma spraying to enhance the surface performance of lightweight alloys.To find out optimum process conditions and achieve desirable coatings,this work focuses on the influence of three important parameters (in-flight par-ticle temperature,impact velocity,and substrate temperature) on the collected splats morphology,coatings microstructure and microhardness.Results show that appropriate combinations of temper-ature and velocity of in-flight particles cannot only completely melt hypereutectic Al-Si-Cu particles,especially the primary Si phase,but also provide the particles with sufficient kinetic energy.Thus,the optimized coating consists of 98.6 ％ of fully-melted region with nanosized coupled eutectic and 0.9 ％of porosity.Increasing the substrate deposition temperature promotes the transition from inhomoge-neous banded microstructure to homogeneous equiaxed microstructure with a lower porosity level.The observations are further interpreted by a newly developed phase-change heat transfer model on quan-titatively revealing the solidification and remelting behaviors of several splats deposited on substrate.Besides,phase evolutions including the formation of supersaturated α-Al matrix solid solution,growth of Si and Al2Cu phases at different process conditions are elaborated.An ideal microstructure (low frac-tions of unmelted/partially-melted regions and defects) together with solid solution,grain refinement,and second phase strengthening effects contributes to the enhanced microhardness of coating.This inte-grated study not only provides a framework for optimizing Al-Si based coatings via thermal spraying but also gives valuable insights into the formation mechanisms of this class of coating materials.
其他文献
The microstructural evolution of purity Pd under 30 keV He+ irradiation at 573 K was investigated by in-situ transmission electron microscopy.The nucleation,growth,merging,annihilation,size change,number density variation,and types of dislocation loops we
The reasonable design of the composition of the composite materials is of great significance to optimized the electromagnetic (EM) wave absorption performance.Herein,the Ni/NiO@C hybrid composites with tunable Ni proportion were successfully synthesized t
The mechanical properties of complex concentrated alloys (CCAs) depend on their formed phases and corresponding microstructures.The data-driven prediction of the phase formation and associated mechanical properties is essential to discovering novel CCAs.T
In current study,the rare-reported solution-driven DyOx films have been prepared to act as the dielectric layer of high performance InZnO/DyOx thin film transistors (TFTs).Annealing temperature depen-dent thermal decomposition,morphology,crystallization b
The increasing electromagnetic hazards including electromagnetic interference and electro-magnetic pollution,which were stemmed from massive usage of electromagnetic technology,have triggered widespread concerns.To cope with this challenge,electromagnetic
Thermal residual stress and strain (TRSS) in particle reinforced metal matrix composites (PRMMCs) are believed to cause strengthening effects,according to previous studies.Here,the representative volume element (RVE) based computational homogenization tec
Grain size dependent strength,known as Hall-Petch relation,has been approved to be valid in crystalline metals and alloys.However,softening would eventually occur as grain size reduced into nanoscale that below a critical value.Hence,it is essential to fi
Dispersoid hardening is a key factor in increasing the recrystallization resistance and mechanical strength of non-heat treatable aluminum-based alloys.Mn and Zr are the main elements that form dispersoids in commercial Al-based alloys.In this work,the an
Alloying is an effective strategy to tailor microstructure and mechanical properties of metallic materials to overcome the strength-ductility trade-offdilemma.In this work,we combined a novel alloy design prin-ciple,i.e.harvesting pronounced solid solutio
Development of low-cost and efficient photocatalytic materials with visible-light response is of urgent need for solving energy and environmental problems.Here,a metal-free two-dimensional (2D) π-conjugated hybrid g-C3N4 photocatalyst with tunable band st