Optimizing neural networks by genetic algorithms for predicting particulate matter concentration in

来源 :重庆大学学报(英文版) | 被引量 : 0次 | 上传用户:rifcumtd111
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
We developed and tested an improved neural network to predict the average concentration of PM10 (particulate matter with diameter smaller than 10 μm) several hours in advance in summer in Beijing. A genetic algorithm optimization procedure for optimizing initial weights and thresholds of the neural network was also evaluated. This research was based upon the PM10 data from seven monitoring sites in Beijing urban region and meteorological observation data, which were recorded every 3 h during summer of 2002. Two neural network models were developed. Model I was built for predicting PM10 concentrations 3 h in advance while Model II for one day in advance. The predictions of both models were found to be consistent with observations. Percent errors in forecasting the numerical value were about 20%. This brings us to the conclusion that short-term fluctuations of PM10 concentrations in Beijing urban region in summer are to a large extent driven by meteorological conditions. Moreover, the predicted results of Model II were compared with the ones provided by the Models-3 Community Multiscale Air Quality (CMAQ) modeling system. The mean relative errors of both models were 0.21 and 0.26, respectively. The performance of the neural network model was similar to numerical models, when applied to short-time prediction of PM10 concentration.
其他文献
采用三维弹塑性大变形热力耦合有限元法,模拟薄板坯连铸液芯铸轧过程中的坯壳变形,分析影响铸坯纵向伸长的主要因素,提出动态反向堆钢理论,对有限元模拟结果和在线热带生产(ISP)工艺中
利用包含置换原子和间隙原子的层错能势力学模型,计算了不同 N含量下 Fe-30Mn-63Si-xN形状记忆合金的层错能计算结果表明, N对合金层错能的作用是先增加后降低(存在一个转折点 p,对应 N含量(质量分数)
研究了等温时效对 SnAg/Cu表面贴装焊点微结构, Sn-Cu金属间化合物生长及其剪切强度的影响,并与常用的62Sn36Pb2Ag/Cu焊点进行了比较,结果表明,在时效过程中, SnAg钎料以较小的反应速率与 Cu发生反应 SnAg焊点显示了较
观察并测试了Zr52.5Cu17.9Ni14.6Al10Ti5块体非晶在不同退火条件下的显微组织与力学性能.等温退火后可以得到尺寸约为30-60 nm金属间化合物相弥散分布在非晶基体上的混合结构
研究了三元双相 Cu—30Ni—25Fe合金在 700—900℃空气中的氧化在相同温度下合金的氧化速率都低于纯铜的,700—800℃的氧化动力学为抛物线规律,在900℃初期为抛物线规律,后期变为线形规律,氧化膜最外层为近
研究了功率模块芯片在 DCB基板上 92.5Pb5Sn2.5Ag钎料焊层的热循环可靠性和裂纹扩展,应用超声波显微镜对裂纹扩展过程进行检测,得到了热循环失效的裂纹扩展数据,采用统一型粘塑性 Anand方程描述了 92.5Pb5Sn2.5Ag的力
以剖分试样真空处理法研究了钢内部裂纹的高温愈合行为,将含预置内部裂纹的 20MnMo钢及 20号和 45号钢试样剖分后封入真空度达 133×10-4 Pa的石英管高温处理 45min.发现试样剖分面上的裂纹均出现愈合迹
我国的公路工程监理是以监理单位为核心,以合同为基础的一项非常重要的工程建设技术服务工作。我们应充分的认识到公路工程监理工作的重要性,只有做好这一工作,才能有效的控制工
随着农业产业结构的不断调整,林下经济已成为具有强大生命力的循环经济模式,它在增加农民收入、培育保护林木资源、加快林业产业结构调整步伐等方面发挥了重要作用。大力推进