施N量和密度对水稻双株秧的效应分析

来源 :绵阳经济技术高等专科学校学报 | 被引量 : 0次 | 上传用户:roycetang
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
通过对水稻双株秧在不同施N量和不同栽插密度下的研究,结果表明:以施用90g/m2N肥、栽240苗/m2处理的有效穗和经济产量最高。就有效穗和经济产量两个经济性状来说,施N量和密度间分别存在极显著和显著的互作效应。在施N量低时(如45g/m2),要有较高的栽插密度(如270苗/m2),才有较高的有效稳和经济产量。因此,在施N量低时应加大栽插密度,以保证足够的有效穗。施N量和密度对颖花数、结实率、株高均无显著影响。因此,栽双株秧必须有较高的N肥施用量和适宜的基本苗数,最后才可能有一个理想的产量。 The results showed that the application of 90g / m2 N fertilizer, planting 240 seedlings / m2, the effective panicle and the highest economic yield. For the two economic traits of effective panicle and economic yield, there is a significant and significant interaction effect between nitrogen application rate and density respectively. In the low N fertilizer (such as 45g / m2), have a higher transplanting density (such as 270 seedlings / m2), have a higher effective stable and economic output. Therefore, the application of N should be increased when planting density density in order to ensure adequate effective panicle. N application rate and density on the number of spikes, seed setting rate, plant height had no significant effect. Therefore, planted double plant seedlings must have a higher N fertilizer application and the appropriate number of basic seedlings, and finally may have an ideal yield.
其他文献
该文参照美国某铝业公司热轧工艺规程,在Gleeble一1500热模拟机上,对3003铝合金多道次热轧过程进行了实验摸拟,通过对变形后试样组织的金相与TEM观察,显微硬度及变形过程的载荷曲
该文主要叙述应用无损检测技术中比较新兴的方法涡流检测技术对铝合金等温锻件表面质量进行无损检测,并把铝合金等温精锻件的涡流检测和渗透检测(荧光)作了比较和分析。为解决铝
采用多极快速凝固制粉工艺制备Al-Cr-Y-Zr合金粉末,通过冷等静压-挤压工艺固结粉末,利用SEM、TEM和力学性能检测等测试手段,研究了粉末粒度对该合金的挤压工艺以及挤压材料组织性能的影响。结果表
该文以高强铝合金为研究对象,探讨了镀层搭配、操作方法及工艺参数对镀层综合性能的影响。结果表明,对于不同性质的铝基材,应选用不同的刷镀工艺。
期刊
涉深水者见蛟龙──从事新闻写作的一点体会桂林南方橡胶(集团)公司谢明智我从事新闻写作已有22年多了,尝尽了当通讯员的酸甜苦辣。甜者,先后在中央、部、省、市级报刊、杂志发表过