【摘 要】
：
In this study, piezoelectric elements were added to a reciprocating friction test bench to harvest friction-induced vibration energy. Parameters such as vibration acceleration, noise, and voltage signals of the system were measured and analyzed. The resul
【机 构】
：
Tribology Research Institute,Southwest Jiaotong University,Chengdu 610031,China;School of Engineerin
论文部分内容阅读
In this study, piezoelectric elements were added to a reciprocating friction test bench to harvest friction-induced vibration energy. Parameters such as vibration acceleration, noise, and voltage signals of the system were measured and analyzed. The results show that the piezoelectric elements can not only collect vibration energy but also suppress friction-induced vibration noise (FIVN). Additionally, the wear of the friction interface was examined via optical microscopy (OM), scanning electron microscopy (SEM), and white-light interferometry (WLI). The results show that the surface wear state improved because of the reduction of FIVN. In order to analyze the experimental results in detail and explain them reasonably, the experimental phenomena were simulated numerically. Moreover, a simplified two-degree-of-freedom numerical model including the original system and the piezoelectric system was established to qualitatively describe the effects, dynamics, and tribological behaviors of the added piezoelectric elements to the original system.
其他文献
The effects of impacting particles from a jet of liquid on the removal of a surface material (on the impacted workpiece) were investigated. Experimental observations show that the cross section of the material removed changed from \'W\'-shaped to \'
Ethylenediamine with two -NH2 functional groups was used as a critical complexing agent in chemical mechanical polishing (CMP) slurries for a high carbon chromium GCr15 bearing steel (equivalent to AISI 52100). The polishing performance and corresponding
To enhance the interface bonding of polyimide (PI)/carbon fiber (CF) composites, CFs were functionalized by introducing a polydopamine (PDA) transition layer, whose active groups provide absorption sites for the growth of molybdenum disulfide (MoS2) nanos
A comparative evaluation of the friction and wear behaviors of 40CrNiMoA steel and Inconel 718 alloy sliding against Si3N4 counterparts was conducted over a large temperature range from room temperature (RT) to 800 ℃. The temperature-dependent tribologica
The dry sliding behavior of three commercial friction materials (codenamed FM1, FM2, and FM3) tested against a Co-free cermet coating produced by high-velocity oxy-fuel (HVOF) on gray cast-iron discs is investigated. FM1 is a conventional low-metallic fri
The rapid development of molecular dynamics (MD) simulations, as well as classical and reactive atomic potentials, has enabled tribologists to gain new insights into lubrication performance at the fundamental level. However, the impact of adopted potentia
Textured surfaces offer the potential to promote friction and wear reduction by increasing the hydrodynamic pressure, fluid uptake, or acting as oil or debris reservoirs. However, texturing techniques often require additional manufacturing steps and costs
The effect of grain boundary (GB) defects on the tribological properties of MoS2 has been investigated by molecular dynamics (MD) simulations. The GB defects-containing MoS2 during scratching process shows a lower critical breaking load than that of inden
以坛紫菜为试验材料,研究不同强度酸雨(pH值分别为5.6、4.5、4.0、3.5)对坛紫菜生理特性的影响.试验中测定了坛紫菜细胞膜透性、抗氧化酶活性及叶绿素荧光参数等生理指标,以比较适当干出和完全浸泡、黑暗和光照条件下酸雨胁迫对坛紫菜生理特性的影响.结果表明:(1)经过不同方式处理的模拟酸雨处理后,适当干出处理的坛紫菜对酸雨的耐受性大于完全浸泡,黑暗处理的坛紫菜对酸雨的耐受性大于光照;(2)坛紫菜的各项生理指标受pH值为3.5的酸雨胁迫的影响最显著,而坛紫菜对pH值为5.6的酸雨胁迫表现出一定的耐受性.该
With the rapid development of industry, the inconsistency between the rapid increase in energy consumption and the shortage of resources is becoming significant. Friction is one of the main causes of energy consumption; thus, the emergence of superlubrici