眼内异物的新诊断法

来源 :眼外伤与职业眼病杂志.附眼科手术 | 被引量 : 0次 | 上传用户:tinnawang
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
根据立体几何原理与勾股定律,按眼球半径为12mm,在x线定位片上找出矢状面、冠状面、水平面的相应x、y、z值后,得出D值。当D=11~12mm时异物位球壁;D<11mm异物位球内;D>12mm 异物位球外。同理得出异物距角膜缘定位环3点钟或9点钟方位的距离;为选择手术切口提供依据。此法在眼球轴长不同者应酌情考虑。 According to the principle of three-dimensional geometry and the law of the Pythagorean, according to the eyeball radius of 12mm, find the sagittal plane, coronal plane, the horizontal plane of the corresponding x, y, z value, the D value. When D = 11 ~ 12mm foreign body ball wall; D <11mm foreign body bit ball; D> 12mm foreign body bit ball. The same reason that the foreign body distance from the corneal edge of the positioning ring 3 o’clock or 9 o’clock position; to provide the basis for the selection of surgical incision. This method in the eye shaft length should be considered as appropriate.
其他文献
声乐作为我们日常生活中一门重要艺术形式,可以陶冶我们的情操,增添我们的生活乐趣。总所周知,声乐的形式各色各样,其中国民族乐是一种较为传统的音乐形式,而美声唱法是不同
低温传输管线是大型低温制冷设备中的关键部件之一,采用高真空多层绝热方式减少低温传输管线的漏热.本文基于Fluent计算平台,分别采用DTRM模型、P1模型、ROSSELAND模型、DO模型、S2S模型对真空环境下的液氦传输管线进行了数值模拟.对比解析计算解,确定了适合液氦低温管真空环境下辐射换热的计算模型,并利用S2S模型对低温传输管线的整体结构进行了模拟.模拟分析表明:S2S模型计算得到的管壁面
中央电视台2005年少儿春节晚会,随着乐韵悠扬的《高山流水》古琴声响起,两位手执长嘴铜茶壶的小兄妹健步地走上前台,面向观众鞠躬之后,兄妹俩反手背负茶壶,头轻微一点,然后
基于双线水平平行盾构施工中土体损失引起的土体变形二维解析解,建立土体变形三维解析解。取不同的纵向位置作为变量,建立土体损失率沿纵向的变化方程;考虑先行隧道施工对后
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
Radio frequency plasma was used to prepare a vanadium catalyst. The results showed that activating time of the catalyst could be shortened quickly and the cata
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
The catalytic activities of TiSiW12O40/TiO2 in synthesizing ethyl ester, propyl ester, n-butyl ester, and amyl ester were reported. It was demonstrated that Ti
于1983和1984年对某厂腈纶车间进行了劳动卫生学和76名工人的眼部情况调查,在另厂选择97名工人作为对照组。调查结果表明:工人在车间丙烯腈浓度2mg/m~3条件下长期作业可致结
汽车发动机在解体检修过程中,要测量缸体各缸孔内径尺寸,凡磨损超过一级标准(0.25mm)的缸孔,就应按规定加级别配置相应新活塞(成组配置),并按制造厂规定的配缸间隙范围,对各