【摘 要】
：
Optical color filters are widely applied in many areas including display, imaging, sensing, holography, energy harvest, and measurement. Traditional dye-based color filters have drawbacks such as environmental hazards and instability under high temperatur
【机 构】
：
InstituteofMicroelectronics,A*STAR(AgencyforScience,TechnologyandResearch),Singapore138634,Singapore
【出 处】
：
PhotonicsResearch
论文部分内容阅读
Optical color filters are widely applied in many areas including display, imaging, sensing, holography, energy harvest, and measurement. Traditional dye-based color filters have drawbacks such as environmental hazards and instability under high temperature and ultraviolet radiation. With advances in nanotechnology, structural color filters, which are based on the interaction of light with designed nanostructures, are able to overcome the drawbacks. Also, it is possible to fabricate structural color filters using standard complementary metal-oxide-semiconductor (CMOS) fabrication facilities with low cost and high volume. In this work, metasurface-based subtractive color filters (SCFs) are demonstrated on 12-inch (300-mm) glass wafers using a CMOS-compatible fabrication process. In order to make the transmissive-type SCF on a transparent glass wafer, an in-house developed layer transfer process is used to solve the glass wafer handling issue in fabrication tools. Three different heights of embedded silicon nanopillars (110, 170, and 230 nm) are found to support magnetic dipole resonances. With pillar height and pitch variation, SCFs with different displayed colors are achieved. Based on the resonance wavelength, the displayed color of the metasurface is verified within the red-yellow-blue color wheel. The simulation and measurement results are compared and discussed. The work provides an alternative design for high efficiency color filters on a CMOS-compatible platform, and paves the way towards mass-producible large-area metasurfaces.
其他文献
改变初始温度以及分别使用甲烷和乙炔气体作碳源时气相爆轰合成碳纳米管,研究了初始温度与不同碳源对碳纳米管的影响。利用X射线衍射(XRD)、透射电镜(TEM)、拉曼(Raman)光谱等对碳纳米管进行表征。结果表明,随着初始温度的升高,所合成的碳纳米管的产量减少且石墨化程度降低,但管壁会变得光滑且管径有所增加。当使用乙炔时,所合成的产物中没有碳纳米管,而是合成了石墨化程度较高的无定形碳,随着催化剂量的增加,产物中碳包覆颗粒增多且包覆层清晰可见,但存在结构缺陷。当初始温度在110~130 ℃时,使用甲烷气体运用气
本文用相对论多组态Dirae—Fock广义平均模型(MCDF-EAL)计算了可能成为激光工作物质的类氮VXVII、CrXVIII、MnXIX和FeXX的2s22p3、2s2p4、2p5、2s22p23s、22s2p23p组态的各44个精细结构能级和33个3s—3p组态跃迁波长。其中关于VXVII、CrXVIII、MnXIX离子3s、3P组态的计算值是本文首次预言的。
微环谐振器是集成光学中的关键器件,它的实际滤波特性会受到输入光功率的影响,但长期以来,微环谐振器的稳态模型仅包含线性光学作用。考虑微环谐振器反馈波导中的光学非线性引入的损耗和相移,以及微环耦合器中光学非线性引入的耦合比改变等因素,推导了考虑自相位调制、双光子吸收和热光效应的微环谐振器的非线性模型。重点讨论了双光子吸收和光学非线性引入的耦合器耦合比改变对微环谐振器陷波深度的影响,仿真结果表明,在热光效应和自相位调制产生谐振谱线频移的同时,功率相关的耦合器耦合比的改变对微环谐振器陷波深度的影响较大。
A three-dimensional (3D) object reconstruction technique that uses pure-phase computer-generated holograms (CGHs) and a phase-only spatial light modulator (SLM) is proposed. The full parallax CGHs are generated by the point source method and the wave-orie
在热的铯原子汽室中,借助双Λ共振四波混频效应,实验研究了入射探针光脉冲和产生的共轭光脉冲的同时慢光传输特性。实验中首先将泵浦光锁定在铯原子D1线超精细跃迁F=4→F′=3上,将探针光调至超精细跃迁F=3→F′=3附近扫描,通过对探针光和共轭光增益特性的分析,给出获得最大增益所对应的最佳铯泡温度约110℃。最后,采用365 ns高斯脉冲作为入射探针光脉冲,研究了探针光脉冲和共轭光脉冲的延迟时间与双光子失谐的关系。通过改变双光子失谐,探针光脉冲的延迟时间可以从40 ns增加到343 ns,相应的群速度从1 8
利用FOI-PERFECT程序对X箍缩进行了3D数值模拟研究,给出了X箍缩的物理图像和动力学过程,探讨了Z箍缩中出现磁重联的可能性,并指出如果双丝Z箍缩中能够出现磁重联,那么X箍缩是更有利于磁重联出现的位形,并且,X箍缩中出现多重X射线暴的一个可能原因是z轴上多个位置出现磁重联。
本文研究了激光束的空间调制问题,得到了栅形、缝形、孔形、扇形调制器的激光束调制场分布式,给出了光强分布图,介绍了初步实验结果.
报道一种使用光折变晶体作为记录材料，可一步实现的消像散体全息阵列照明器。根据记录波长与再现波长，计算出最佳的记录角度与再现角度，使再现时由于记录与再现波长不同引起的像散得到补偿。
在太赫兹厚度无损检测中,针对薄涂层上、下表面回波不可分的问题,测定频率为0.2~7 THz的普通面漆涂层的光学参数,根据其在频率为0.2~2 THz时的光谱特性,采用折射率常数模型和消光系数常数模型建立了反射式太赫兹波传播仿真模型。将仿真波形与实际太赫兹检测波形的差值方程组作为目标函数,提出最小二乘厚度优化方法,同时引入太赫兹发射器与样品间的距离参数对目标函数进行优化。设计具有不同阶梯厚度的面漆涂层样件进行无损检测厚度成像实验。实验结果表明:所提方法对定量无损检测精度有显著提高效果,对面漆涂层来说,