【摘 要】
：
A quasi-solid-state lithium battery is assembled by plasma sprayed amorphous Li4Ti5O12 (LTO) electrode and ceramic/polymer composite electrolyte with a little l
【机 构】
：
Guangxi Key Laboratory of Automobile Components and Vehicle Technology,Guangxi University of Science
论文部分内容阅读
A quasi-solid-state lithium battery is assembled by plasma sprayed amorphous Li4Ti5O12 (LTO) electrode and ceramic/polymer composite electrolyte with a little liquid electrolyte (10 μL/cm2) to provide the outstanding electrochemical stability and better normal interface contact. Scanning Electron Microscope (SEM), Scanning Transmission Electron Microscopy (STEM), Transmission Electron Microscopy (TEM), and Energy Dispersive Spectrometer (EDS) were used to analyze the structural evolution and performance of plasma sprayed amorphous LTO electrode and ceramic/polymer composite electrolyte before and after electrochemical experiments. By comparing the electrochemical performance of the amorphous LTO electrode and the traditional LTO electrode, the electrochemical behavior of different electrodes is studied. The results show that plasma spraying can prepare an amorphous LTO electrode coating of about 8 μm. After 200 electrochemical cycles, the structure of the electrode evolved, and the inside of the electrode fractured and cracks expanded, because of recrystallization at the interface between the rich fluorine compounds and the amorphous LTO electrode. Similarly, the ceramic/polymer composite electrolyte has undergone structural evolution after 200 test cycles. The electrochemical cycle results show that the cycle stability, capacity retention rate, coulomb efficiency, and internal impedance of amorphous LTO electrode are better than traditional LTO electrode. This innovative and facile quasi-solid-state strategy is aimed to promote the intrinsic safety and stability of working lithium battery, shedding light on the development of next-generation high-performance solid-state lithium batteries.
其他文献
以飞机虚拟维修训练的实际应用为需求,分析了飞机虚拟维修训练仿真模型基本开发流程和技术手段,解决了开展大规模工程推广应用中的技术瓶颈。针对维修训练仿真模型开发效率低、更新困难等突出问题,提出了支持大规模工程应用的快速开发流程,并对支撑虚拟维修训练仿真模型快速开发的维修任务建模、仿真模型装配、仿真模型更新3项关键技术的原理及实现途径进行了论述。最后用某型号工程实例进行了技术开发实现并通过应用验证。
分数阶模型需要辨识更多的参数,为了建立高精度的分数阶模型,提出一种应用于分数阶系统辨识的改进差分进化算法。在变异策略中基向量从最优个体种群中随机选取,在搜索过程中根据成功变异个体的信息自适应调整缩放因子和交叉概率因子,提高算法的勘探和开采能力。通过求解5个测试函数,证明了改进算法具有较强的求解能力。以永磁同步电机的分数阶模型为例,辨识结果表明:改进差分进化算法在求解精度和收敛速度上具有更好的性能。
城镇化背景下,社会网络弱连接关系增多,对弱势语言保护提出了挑战。基于改进的agent社会圈子网络建模方法构建了具有远程弱连接关系的新型社会网络;不同人群语言演化机制上除考虑语言地位和语言人口比例的影响外,引入了双语者对单语者向双语者转变的影响力、语言态度和网络连接关系对语言选择行为的影响新机制;给出了改进的agent语言水平和垂直传播模型。计算实验结果表明:在社会网络弱连接关系增多背景下,培养积极
The dielectric capacitor has been widely used in advanced electronic and electrical power systems due to its capability of ultrafast charging–discharging and u
High-thermally conductive AlN-based microwave attenuating composite ceramics with spherical graphite (SG) as the attenuating agent were fabricated through hot-p
Photocatalysts with the photocatalytic “memory” effect could resolve the intrinsic activity loss of traditional photocatalysts when the light illumination is
风电机组传感器受环境干扰,导致采集的信号存在差异,从而对风电机轴承的故障诊断结果产生影响。为提高故障诊断的可靠性,提出一种多源信号故障诊断方法。提取轴承振动信号、噪声信号、温度信号的时域、频域特征作为故障特征,利用经贝叶斯优化算法优化隐藏层节点结构的堆叠降噪自编码器对故障特征进行融合,采用Softmax对融合的故障特征进行分类。实验表明:该方法的故障准确率比单一信号进行故障诊断的方法更高,并且混合
The Mn1.95-xCo0.21Ni0.84SrxO4 (MCNS) (0 ≤ x ≤ 0.15) based negative temperature coefficient (NTC) materials are prepared by co-precipitation method. The replac
冲击对系统可靠性产生一定影响,而如何量化冲击载荷的影响程度成为系统可靠性分析的关键。在退化失效与突发失效竞争的基础上,研究系统受到不同冲击强度影响下的可靠性模型精度问题。在失效阈值可变的情况下,以极值冲击描述冲击过程,Wiener过程描述两类失效的退化过程。针对不同强度冲击对系统的影响下,考虑对冲击进行载荷区域的划分,建立两类失效过程的分布函数,提出了系统竞争失效的可靠度模型。结合Sandia微引
Lead-free Na0.5Bi0.5TiO3 (NBT) ceramics were prepared via a conventional oxide-mixed sintering route and their electrical transport properties were investigated