【摘 要】
：
AA6005A-T6 aluminum hollow extrusions were friction stir welded at a fixed high welding speed of 2000 mm/min and various rotation speeds.The results showed that the heat-affected zone (HAZ) retained the similar grain structure as the base material except
【机 构】
：
Luoyang Ship Material Research Institute, Luoyang 471023,China;State Key Laboratory of Advanced Weld
论文部分内容阅读
AA6005A-T6 aluminum hollow extrusions were friction stir welded at a fixed high welding speed of 2000 mm/min and various rotation speeds.The results showed that the heat-affected zone (HAZ) retained the similar grain structure as the base material except some grain coarsening,and the density of dislocations and β\'precipitates were almost unchanged,indicating that the high welding speed inhibited the coarsening and dissolution of β“ precipitates via fast cooling rate.The thermo-mechanically affected zone (TMAZ) was characterized by elongated and rotated grains,in which a low density ofβ\'precipitates and the highest density of dislocations were observed.The highest heat input and severest plastic deformation occurring in the nugget zone (NZ) resulted in the occurrence of dynamic recrystallization and a high density of dislocations.Hence,all the β” precipitates and most of the β\'precipitates dissolved into the matrix,and a few β\'precipitates were transformed into β precipitates.The microhardness was controlled by the precipitation and solution strengthening in the HAZ,by the dislocation and precipitation strengthening in the TMAZ,and by the fine-grain and dislocation strengthening in the NZ.With the increase in rotation speed,the peak and the lowest microhardness value increased monotonously.
其他文献
The effect of a pulsed electric current on the residual stress evolution of metal materials has been investigated.It was found that the surface and internal residual stresses in the as-quenched samples were reduced dramatically by electropulsing.A large n
A 2.5-mm Fe72.5B15.6Si7.8Nb1.7Zr1.7Cu0.7 glassy rod was successfully fabricated using copper mold casting.The introduction of Cu resulted in the formation of large quantities of α-Fe nanoparticles embedded in the glassy matrix after isothermal annealing.T
A systematic study of nitric acid passivation was investigated to enhance the general corrosion resistance of biomedical high-nitrogen nickel-free stainless steels (HNSs).After passivation,the corrosion rate of HNS could dramatically reduce to 1/20 of the
The void formation and plastic deformation micromechanisms of a cold-rolled DP600 steel during tensile loading were studied by scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD).The SEM observations revealed that the main void
Mg alloys,as a new generation of biodegradable bone implant materials,are facing two tremendous challenges of enhancing strength and reducing degradation rate in physiological environment to meet clinical needs.In this study,tricalcium phosphate (β-TCP) p
Friction stir additive manufacturing is a newly developed solid-state additive manufacturing technology.The material in the stirring zone can be re-stirred and reheated,and mechanical properties can be changed along the building direction.An integrated mo
T6-treated 20 wt％ B4Cp/6061Al sheets were joined under welding speeds of 400-1200 mm/min by friction stir welding (FSW) with a threaded cermet pin.The macro-defect-free FSW joints could be achieved at high welding speeds up to 1200 mm/min,but larger plung
W-Y2O3 composite nanopowders prepared via wet chemical method exhibit unique morphologies and microstructures.The yttrium addition during chemical reaction process affects not only the composition of tungsten acid hydrate precursors,but also the reduction
In this work,the influence of the Zener-Hollomon (Z) parameter on the microstructure and mechanical properties of copper subjected to friction stir welding (FSW) was investigated.Liquid N2 cooling was conducted to control the cooling rate after the FSW.Th
X80 pipeline steel plates were friction stir welded (FSW) under air,water,liquid CO2 + water,and liquid CO2 cooling conditions,producing defect-free welds.The microstructural evolution and mechanical properties of these FSW joints were studied.Coarse gran