【摘 要】
：
Impact drop tests are routinely used to examine the dynamic performance of rockbolts.Numerous impact tests have been carried out in the past decades on independ
【机 构】
：
Norwegian University of Science and Technology (NTNU),Trondheim,Norway;University of Toronto,Toronto
论文部分内容阅读
Impact drop tests are routinely used to examine the dynamic performance of rockbolts.Numerous impact tests have been carried out in the past decades on independently designed,constructed and operated testing rigs.Each laboratory has developed testing procedures;thus,the results are often re-ported in different ways by various laboratories.The inconsistency in testing procedures and reporting formats presents a challenge when comparing results from different laboratories.A series of impact tests of identical rockbolts was carried out using the direct impact method (i.e.the mass free-fall method) on the rigs in four laboratories in different countries.The purpose of these tests was to investigate the level of consistency in the results from the four rigs.Each rig demonstrated a high level of repeatability,but differences existed between the various rigs.The differences would suggest that there is noticeable equipment-dependent bias when test results obtained from different laboratories are compared.It was also observed that the energy dissipated for the plastic displacement of the bolt was smaller than the impact energy in the tests.The average impact load (AIL) and the ultimate plastic displacement (D) of the bolt describe the ultimate dynamic performance of the bolt.In the case where the bolt does not rupture,the specific plastic energy (SPE) is an appropriate parameter in describing the impact performance of the bolt.Two other relevant parameters are the first peak load (FPL) and the initial stiffness (K) of the bolt sample.The information from this test series will guide the formulation of standardised testing pro-cedures for dynamic impact tests of rockbolts.
其他文献
夏花生常因汛期雨水偏多形成涝渍灾害而减产,探索不同耕作方式下涝渍持续日数对花生光合特性及产量的影响,可为花生涝渍动态监测评估和农业防灾减灾提供参考。选择2019年、2020年每年6—9月,在花生主产区河南驻马店土壤质地为粘土的大田平作、垄作方式下,以豫花22为试验材料,将花生产量形成过程分前期、中期、后期3个时段,分别设计3 d,5 d,7 d,9 d灌水处理。结果表明:相同过程灌水量条件下,垄作比平作涝渍持续日数减少1~5 d,其中淹涝日数偏少3~5 d;3 d灌水处理的涝渍持续日数4~5 d,叶绿素含
为探讨高温对猕猴桃叶片光合机构的影响,建立基于叶绿素荧光反应的高温热害识别指标,利用叶绿素快速荧光诱导动力学分析技术,研究不同温度胁迫下猕猴桃叶片8类叶绿素荧光的变化特征。结果表明:单位面积捕获的光能、单位面积有活性的反应中心数量、300 μs处相对可变荧光强度差值在30℃≤T≤54℃时均受温度胁迫影响,属光系统Ⅱ敏感位点参数,其中单位面积捕获的光能、单位面积有活性的反应中心数量随温度升高呈直线下降趋势,300 μs处相对可变荧光强度差值随温度升高呈指数上升趋势;初始荧光、最大荧光、最大光化学效率、单位面
In the last two decades,significant research has been conducted in the field of automated extraction of rock mass discontinuity characteristics from three-dimensional(3D)models.This provides several methodologies for acquiring discontinuity measurements f
“十四五”规划对未来经济规划了什么— 金融视角,也就是未来5年推动经济高质量发展往哪里去的问题.要求我们必须立足新发展阶段,贯彻新发展理念,构建新发展格局.要坚定不移
随着机载光电设备对姿态实时性和精度要求的不断提高,直接采用捷联方式安装于吊舱内部的小型惯性导航单元,配合全球导航卫星系统进行组合导航的方案开始逐渐得到应用。吊舱、飞机、惯导间由于空间安装位置的不同,吊舱框架角的不断变化会引入额外的杆臂相关误差。详细推导了吊舱、飞机与惯导间姿态转换关系,提出了一种改进的在线补偿杆臂效应参数的组合导航滤波模型。飞行试验证明了改进的组合导航模型能够有效估计吊舱-惯导与吊舱-飞机间的杆臂参数,在线估计精度可达到厘米级,输出航向精度较传统组合导航算法提高了1倍。
针对水下环境影响导致DVL回波个数小于4,常规惯性/DVL组合导航无法进行,对DVL的回波信息利用不充分的问题,提出了一种基于波束域信息的SINS/DVL组合导航方法。直接将DVL测量的波束域信息与惯导系统速度转化得到的频移差值作为观测量,考虑惯导以及DVL的多项误差,建立基于频移观测量的卡尔曼滤波模型,实现对惯导系统误差和DVL误差估计与修正。数学仿真及试验结果表明:所提方法与基于速度匹配的算法相比,组合导航定位精度提高30%以上,多普勒信息的利用率以及对水下复杂环境的适应性均有显著提升。
基于视觉的同时定位与建图(VSLAM)已广泛应用于室内机器人导航任务中。面向自主导航及地图复用性的需求,实时三维重建需克服环境光照不均、角点提取数量及质量不高、位姿漂移等问题。为此,提出构建一类基于稀疏直接法单尺度Retinex的SLAM(RDSOL)系统。RDSOL继承稀疏直接法里程计(DSO)主体框架,算法上打破后者前端光度标定及无回环检测模块的设计,通过单尺度Retinex图像增强及添加闭环
To investigate the longitudinal deformation profile(LDP)of a deep tunnel in non-hydrostatic condition,an analytical model is proposed in our study.In this model,the problem is considered as a superposition of two partial models,and the displacement field
针对复杂环境中双目视觉/惯性里程计系统模型不固定和量测噪声易发生变化的问题,提出了基于滤波器估计的紧耦合视觉惯性里程计(VIO)信息融合方法。将交互式多模型(IMM)估计与多状态约束卡尔曼滤波(MSCKF)算法相结合提出一种交互式多模型多状态约束卡尔曼滤波(IMM-MSCKF)算法。该算法以MSCKF为模型匹配子滤波器,将各子滤波器的输入、输出进行交互融合,实现对VIO系统状态估计。通过KITTI
水下重力场匹配导航的SITAN算法综合了扩展卡尔曼滤波技术和地形随机线性化技术,具有实时性好、可操作性强等特点。针对其在粗差探测方面的不足,引入抗差估计方法,通过设置调节因子,降低了异常点状态矩阵和增益矩阵等对下一位置点的影响,来改善导航位置精度,增强可靠性。仿真试验结果表明,采用一般SITAN算法的水下重力匹配导航位置精度均值为2~3 n mile,引入抗差方法后,导航位置精度保持在1 n mile以内,精度水平提升50%以上。抗差估计方法用于水下重力匹配导航,具有较好的精度改善作用。