Effect of BaSO4 on phase composition and sintering process of iron ore fines

来源 :钢铁研究学报(英文版) | 被引量 : 0次 | 上传用户:oldfan48
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Iron ore containing BaSO4 may have a senes of effects on the quality of the sinter and performance of the blast furnace.Thus,the effect mechanism of BaSO4(0-6.0 mass%)on the compressive strength,mineral composition,and microstructure of the sinter was investigated.The experimental results show that the compressive strength of the sintered samples initially increases and then decreases when the BaSO4 content increases from 0 to 6.0 mass%,reaching a peak value of 12.78 kN with a BaSO4 content of 1.0 mass%.Thermal analysis indicates that BaSO4 initially decomposes to produce BaO at 1468 K in the presence of iron ore.BaO combines with Fe2O3 forming barium ferrite(Ba2Fe6O11),which exists in the sintered sample with a granular form.BaO also dissolves in calcium ferrite and slag to promote the formation of calcium ferrite and barium glass,respectively.The content of needle-like calcium ferrite gradually increases and then decreases with the increase in BaSO4 content.Hematite exists in a plate-like form.The generation of dicalcium ferrite is promoted by increasing the BaSO4 addition from 2.0 to 6.0 mass%.
其他文献
利用SEM、TEM、XRD、EPMA等手段,研究了水冷、空冷和炉冷对奥氏体基FeMnAlC钢微观组织和力学性能的影响.研究结果表明,3种冷却工艺都获得了以奥氏体为基体的微观组织,均含有大量孪晶,随冷却速度的降低,沿晶界析出的铁素体和κ碳化物逐渐增多,微观结构呈现出从以位错为主到调制结构再到矩形畴界的转变过程,组织演变受合金元素的配分行为控制.与水冷样品相比,κ碳化物的析出导致炉冷和空冷样品的强度提升约200 MPa,铁素体和κ碳化物的晶界析出行为导致冲击吸收能量降低约100 J.
Based on the thermal simulation method,a systematical analysis was conducted on the effect of welding peak temperature and the cooling time that takes place from 800 to 500℃on microstructure,precipitates,substructure and microhardness of the reheated coar
Optimization of mathematical model of flow field in slab continuous casting mold was performed by means of industrial measurement and mathematical modeling.The rod deflection method was used to quantitatively measure the velocities near the mold surface a
In order to improve the production efficiency of electroslag remelting process and the solidification quality of electroslag ingot,a novel electroslag furnace with electromagnetic stirring was designed and the effects of external magnetic field and differ
Based on the free volume theory,lattice model,the Scatchard-Hildebrand theory,novel expressions of configuration partition function and excessive Gibbs free energy and component activity coefficients of solid solutions were developed using configuration p
To reduce internal residual stress and homogenize micro-property of hot-rolled ferrite steel,the cold compression deformation method with small reduction rate has been performed in the hot-rolled samples,and X-ray diffraction and nanoindentation test have
The reactions between CO2 gas and liquid Fe-C alloy with different initial carbon concentrations at 1873 K were investigated using experimental results,thermodynamic equilibrium,and kinetic analysis.The average CO2 conversion is greater than 80%when the c
The sliding wear property of high-carbon nanostructured bainitic bearing steel with the equal initial hardness and different microstructures was investigated,and the reasons for the difference of wear resistance between the cementite-bearing(CB)and cement
采用高通量场发射扫描电镜结合图像批处理技术以及全自动显微维氏硬度分析技术对2种不同成分(W1和W2)的火车车轮轮辋踏面附近较大范围内的显微组织和硬度进行了原位统计分布表征,探究了轮辋靠近踏面的关键区域铁素体面积分数和珠光体片层间距的分布规律.通过大尺度原位统计分布表征结果可以发现,2种车轮铁素体面积分数自踏面往里均呈现逐渐增加的趋势,但固溶强化元素Si和沉淀强化元素V的含量差异以及W2车轮所采用更为精细的阶梯式淬火工艺对车轮的微观组织和硬度的定量分布有较大影响.固溶强化和沉淀强化元素含量较少的W1车轮的铁