【摘 要】
：
SiCp/Al composites are difficult-to-cut materials.In recent years,electrical arc discharge machining has been developed to improve the machinability of these materials.However,there is a big challenge to build a satisfactory heat transfer model of SiCp/Al
【机 构】
：
School of Mechanical and Electronic Engineering,Nanjing Forestry University,Nanjing 210037,China;Dep
论文部分内容阅读
SiCp/Al composites are difficult-to-cut materials.In recent years,electrical arc discharge machining has been developed to improve the machinability of these materials.However,there is a big challenge to build a satisfactory heat transfer model of SiCp/Al composites in the arc machining.This is not only because of the material property difference between the reinforcement and matrix material but also because of the micro-dimension SiC reinforcements.This paper established a new heat conduction simulation model considering the SiC particle-Al matrix interface and the phase change effects in a single-pulsed arc discharge of SiCp/Al composites.A novel SiC particle-Al matrix cell geometric model was designed firstly.Then,the temperature distribution at a different depth from the workpiece surface was analyzed,the influence of sic volume fraction on temperature field was studied,and the contribution of the interface thermal resistance and latent heat were explained.To demonstrate the validity of the new numerical model,comparisons and verifications were employed.Finally,the method of improving the model was proposed and the machining mechanism of arc discharge of SiCp/Al matrix materials was discussed.It was found that high tem-perature is prone to concentrate on the surface layers of the workpiece especially when the SiC frac-tion is high,also,the temperature fluctuates respectively at the evaporation point of aluminum and SiC,and the SiC-Al resistance has less influence on temperature distribution compared to latent heat,etc.The model build in this work improves the simulation accuracy observably compared to the previous model,and the simulation work will help to acquire a detailed mechanism of mate-rial removal of SiCp/Al composites in the arc discharge machining.
其他文献
A loss of ground directional stability can trigger a high-speed Unmanned Aerial Vehicle(UAV) to veer off the runway.In order to investigate the combined effects of the key structural and oper-ational parameters on the UAV ground directional stability from
In modern gas turbines,the High Pressure Turbine (HPT) is exposed to an extreme ther-mal environment due to the burned gases leaving the combustor.The burned gases are character-ized by flow and temperature distortions that effect the aerodynamics and hea
Three Plasma Synthetic Jet Actuators (PSJA) under the high-frequency actuation are used to control the Shock Wave Boundary Layer Interaction (SWBLI),a high-speed schlieren image processing method based on spatial Fourier transform as well as snapshot prop
This paper considers effects of Rotating Inlet Distortion (RID) on a two-stage axial com-pressor and the stabilization effects of a casing treatment subjected to the considered RID.In multi-spool engines,the downstream compressor suffers a RID when the up
In this paper a novel design method of aerodynamic configuration is proposed to inte-grate forebody,strut and inlet for strutjet engine,and a model at design point of Mach number 6 is generated to investigate the aerodynamic performance by both simulation
Blade Tip-Timing (BTT) has been regarded as a promising way of on-line blade vibra-tion monitoring.But blind multi-band BTT vibration reconstruction is a big challenge under vari-able speeds and under-sampling.In order to deal with it,a novel Compressed S
The aircraft system has recently gained its reputation as a reliable and efficient tool for sensing and parsing aerial scenes.However,accurate and fast semantic segmentation of high-resolution aerial images for remote sensing applications is still facing
To investigate the effect of tip clearance size on cavitation characteristics in a turbopump inducer,a series of experiments have been conducted in a newly developed visualization test facility using room temperature water as working fluid.The pressure fl
文章对辽宁省旱涝成因以及前期海温外强迫特征进行了剖析。研究表明辽宁夏季降水存在显著的季节内特征,初夏主要受东北冷涡的影响,两者之间存在显著负相关关系。初夏东北冷涡强度指数与两个海温关键区的相关系数,分别为0.38和0.45,均超过信度为0.01的检验。
The low-speed wind tunnel experiment is carried out on a simplified aircraft model to explore the influence of wing flexibility on the aircraft aerodynamic performance.The investigation involves the measurements of force,membrane deformation and velocity