丙酸睾丸酮加强米非司酮终止50~68天早孕的研究

来源 :中国计划生育学杂志 | 被引量 : 0次 | 上传用户:fwaiting
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
为探讨丙酸睾丸酮(简称丙睾)加强米非司酮终止50~68天早孕的作用,本文以68例丙睾、米非司酮、卡孕栓(PG05)药物流产为加丙睾组,30例米非司酮、卡孕栓药物流产为对照组,比较其临床效果及药效机制。临床两组间比较,加丙睾组完全流产率95.59%,对照组为76.67%,明显高于对照组(P<0.01),加丙睾组流产后出血天数为11.17天,对照组15.39天,少于对照组(P<0.05)。从流产物病理及组化改变上观察,对照组有绒毛水肿、滋养层细胞变性、坏死,周围有糖蛋白包绕,蜕膜轻度坏死。加丙睾组除有上述绒毛病变外,突出的改变是蜕膜细胞连同滋养层柱细胞大量坏死,残存的蜕膜细胞间的胶原纤维肿胀、变性,并有网状纤维破坏。结果显示序贯应用该三种药,对终止50~68天早孕确有高效。并皆作用于受体,系分子水平药物,有广阔发展前景。 In order to explore the role of testosterone propionate (C) in enhancing the effect of mifepristone on the termination of early pregnancy by 50 to 68 days, 68 cases of testosterone, mifepristone and carbamazepine (PG05) 30 cases of mifepristone, cardiopulmonary arrest drug abortion control group, compare its clinical efficacy and efficacy mechanism. Clinical comparison between the two groups showed that the rate of complete abortion was 95.59% in the testis group and 76.67% in the control group, significantly higher than that in the control group (P <0.01). The number of bleeding days in the testis group was 11.17 days after abortion and 15.39 days in the control group Less than the control group (P <0.05). Observed from the flow of the pathological and histological changes, the control group has villous edema, trophoblast cells degeneration and necrosis, surrounded by glycoprotein, decidual mild necrosis. In addition to the addition of the testis group villus lesions, the prominent change is a large number of decidual cells along with trophoblast columnar necrosis, residual decidual cells between the collagen fibers swelling, degeneration, and destruction of reticular fibers. The results show that sequential application of the three drugs, the termination of early pregnancy 50 to 68 days is indeed efficient. And all act on the receptor, Department of molecular level drugs, have broad prospects for development.
其他文献
目的:评估在骨盆漂浮体位下通过踝关节后外联合后内侧入路治疗后Pilon骨折的临床疗效.方法:选取2016年6月至2019年6月收治的后Pilon骨折患者24例,采用骨盆漂浮体位从踝关节后
目的:探讨手法复位结合微创改良入路弹性髓内钉逆行内固定治疗成人肱骨干骨折的方法,并评价其疗效.方法:回顾性分析从2012年1月至2019年10月,以手法复位结合微创改良入路弹性
本文分析了南京市900MHz蜂窝式无线移动电话的发展现状和市场定向,提出了移动电话的发展规模及移动电话用户与市话用户间的比例关系,并就如何把握移动电话的发展走向提出了几
本文主要对加工中心侧面周边孔加工夹具进行了设计,设计方案一,利用数控转台进行分度回转加工,转台的分度盘上直接安装定位板,定位板上安装一气缸,将工件装在定位板上,利用摆杆压紧
本文介绍了在双金属材质上加工高精度斜孔的工艺方法和过程.综合采用精铣+精磨抛光加工、五轴车铣复合加工编程、数控加工虚拟仿真分析等技术和方法,不需要专用钻模的情况下
目的:探讨HR-HPV及LR-HPV的消退规律,为细胞学检查正常的HPV阳性人群制定合理的个体化诊疗方案。方法:对2007年1月~2008年12月在吉林大学第二医院妇科门诊妇科体检宫颈细胞学
M1432磨床是一款型式较老的普通外圆磨床,它曾经大量应用在企业生产一线,以耐用、稳定而著称。现在在加工中,大量的陶瓷工件需要由一台M1432磨床磨削,加工时伴有强冷却液喷射,生产
本文针对某药筒在滚口过程中出现的技术质量问题,进行了深刻剖析,提出对滚口刀架的改进方案.通过不断调试、查找原因,决定将手摇式结构改为杠杆式结构,并对该结构原理、类型
双曲面、内定位凸台薄壁拱形零件加工厚度为50-0.08,是大直径内、外双曲面且在内孔处有一定位凸台设计的零件,零件设计使用了流动性好的纯铜材料,各尺寸公差、形状、位置公差
会议
1995年在11月至1996年元月,我市中小学校发生一起风疹流行.集中在4所中小学校.发病例72人.发病率为937.74/10万,现将流行情况及处理措施报道如下:1流行经过1996年11月20日,北海市第一