【摘 要】
：
A rapid and cost-effective method for fabricating mini lens arrays is proposed. The lenses are made of silicone oil droplets and filled inside a polydimethylsiloxane (PDMS) elastomer. The lens arrays of different initial focal lengths and apertures can be
【机 构】
：
EngineeringResearchCenterofOpticalInstrumentandSystem,MinistryofEducationandShanghaiKeyLaboratoryofM
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
A rapid and cost-effective method for fabricating mini lens arrays is proposed. The lenses are made of silicone oil droplets and filled inside a polydimethylsiloxane (PDMS) elastomer. The lens arrays of different initial focal lengths and apertures can be fabricated by using the droplets of different volumes. Due to good elastic behavior of PDMS, the droplet lenses can be flexibly deformed, and the focal length and numerical aperture can be tuned by applying an external force on the PDMS elastomer. Furthermore, an apparatus for focal length tuning is designed and employed in the imaging system.
其他文献
We report a method to reduce the detection delay temperature drift for a single-photon detector based on the avalanche photodiode (SPAD). Both the SPAD and the comparator were temperature stabilized, resulting in an ultra-low temperature drift at 0.01 ps/
Signal degradation due to physical impairments may result in unacceptable bit-error rates of received signals at the destination. Based on earlier work, we study the impairment-aware quality of service (QoS) provisioning problem in dual-header optical bur
通过氢化物气相外延(HVPE)方式在蓝宝石衬底上获得了GaN微米碟,其几何形态为规则的正六边形且表面平整,直径约为27 μm,高度为15 μm。光致发光(PL)实验结果表明,微米碟垂直方向和水平方向的光学谐振模式存在差异,其中水平方向支持回音壁模式(WGM)振荡。在室温条件下采用高能脉冲激光照射微米碟,当激励光功率超过7.8 μW时,PL光谱在波长374 nm附近获得多模式激光信号,其中WGM激光占优势,品质因子可达3742。最后采用COMSOL仿真软件对谐振腔进行光场模拟,并分析了其光学模式特性。
本文从量子力学出发,讨论了面沟道辐射的一般论证.在非简谐近似下,描写了正电子面沟道辐射的频谱辐射.同实验比较表明,二者基本符合.
A high-quality Cr3 :CdWO4 single crystal at a size of approximately \Phi 25 \times 80 mm is grown using the Bridgman method with CdO, WO3, and Cr2O3 as raw materials and their molar ratio of 100:100:0.5. The temperature gradient of solid-liquid interfac
荧光法作为一种非侵入性测量手段,能够实现水体藻类初级生产力的快速测量。然而在目前初级生产力荧光动力学分析中,藻类光合尺寸单元通常采用固定值,导致初级生产力测量结果发生偏差,特别是水体存在蓝藻时尤为明显。光合尺寸单元定义为光合反应中心浓度与叶绿素浓度的比值。为获得准确的水体藻类光合尺寸单元以提高初级生产力测量结果的准确性,利用激发荧光光谱分析水体蓝藻和其他真核藻占比,以此为基础对混合藻样品光合尺寸单元进行校正,并提出一种基于光合尺寸单元校正的荧光法藻类初级生产力测量方法。纯种样品和混合样品初级生产力比对测试
A network structure surface-enhanced Raman scattering (SERS)-active substrate is fabricated by adding Ag sol dropwise on adhesive tape. Scanning electron microscope (SEM) is employed to characterize the structure of the as-prepared substrate. The substrat
由国际研究和发展有限公司为英国核燃料有限公司设计的、用以帮助先进的气冷反应堆研究的激光打孔机现已完成验收试验。
干扰超前量的设置对激光角度欺骗干扰的成功概率有着重要的影响。通过建立激光角度欺骗干扰中制导信号和干扰信号被波门录取的概率模型，推导并验证了最优干扰超前量公式。通过仿真研究了不同影响因素对最优干扰超前量设置的影响。仿真结果表明：波门宽度、制导信号脉冲间隔误差、干扰信号脉冲间隔误差对最优干扰超前量的设置均有较大影响。最优干扰超前量与波门宽度成正比，制导信号脉冲间隔误差越大、干扰信号脉冲间隔误差越小，最优干扰超前量越大。设置合适的干扰超前量可以大幅度提高激光角度欺骗干扰的干扰概率。