Applications of Symmetry and Pattern Repetition for Periodic Structures Using Parameterized Level Se

来源 :中国计算力学大会2018暨国际华人计算力学大会2018 | 被引量 : 0次 | 上传用户：wm3033

【摘要】

：

【作者】

：

Peng Wei Yang Liu Zuyu Li

【机构】

：

State Key Laboratory of Subtropical Building Science,School of Civil Engineering and Transportation,

【出处】

：

中国计算力学大会2018暨国际华人计算力学大会2018

【发表日期】

：

2018年10期

【关键词】

：

Symmetry and pattern repetition Topology Optimization Parameterized level set me

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　In practical engineering applications,large-scale structures are often disassembled into small-scale components to satisfy transportation,installation,recycling or other practical constraints.Generally,the components are designed with same or similar patterns for concern of manufacturing convenience.

其他文献

High-order multi-scale asymptotic analysis of axisymmetric piezoelectric problem for composite struc

The second-order two-scale(SOTS)asymptotic piezoelectric model is presented for the axisymmetric composites.The structure considered is assumed to be homogeneous in circumferential direction,and have

会议

Axisymmetric piezoelectric problemPeriodic composite materialsMulti-scale Expa

New periodic orbits for the planar Newtonian three-body problem

The famous three-body problem can be traced back to Isaac Newton in the 1680s.In the 300 years since this “three-body problem” was first recognized,only three families of periodic solutions had been f

会议

three-body problemperiodic orbitsclean numerical simulation (CNS)

Integrated topology optimization design of structures and lattice materials

This paper presents a novel concurrent topology optimization approach for finding the optimum topologies of macrostructures and their corresponding parameterized lattice microstructures in a integrate

会议

Topology optimizationConcurrent designParameterized microstructuresMulti-scal

Structural topological optimization of three-phase solid materials

Multi-material structural topology optimization is to find the best distribution of more than one materials under given loads and constraints,which is an effective means of conceptual design of lightw

会议

Topological optimizationThree-phase solid materialsICM method

Crashworthiness improvement of composite tubes by experiments and simulations

For energy absorption structures of a particular material,changing their geometrical dimensions can generally cause great change of their energy absorption capacity.

会议

CrashworthinessGFRPOptimizationPly angleFoam fillingThin-wall tube

软质防爆毯防爆性能及机理的数值模拟研究

防爆毯是反恐处突中常用的临时防爆装置，通常由软质复合材料加工而成。为了探索防爆毯在近场爆炸载荷作用下的性能及其吸能机理，采用有限元法，结合纤维复合材料连续介质损伤本构模型，数值模拟研究了软质防爆毯和围栏在爆炸冲击作用下的动态响应，分析了材料的损伤机理和结构的变形失效模式，获得了冲击波的传播与衰减规律，并探讨了泄爆孔的设计对防爆毯防爆性能的影响，可为防爆产品的设计和优化提供参考。

会议

防爆毯纤维复合材料爆炸冲击波数值模拟

设备布局及频带约束对隔振结构拓扑优化结果的影响

在车辆工程、机械工程以及航空航天等领域中，由于外部激励、机构运转及摩擦等因素的存在，系统都会受到振动负面效应的影响，因此，通常会设计各种隔振结构来解决或缓解这类问题。本文以一个简易的隔振结构为对象，分别研究了设备布局和频带约束两类问题对隔振结构拓扑优化结果的影响。

会议

隔振结构设备布局拓扑优化频带约束参数优化

Dynamic response optimization design under harmonic base acceleration excitations of lattice filling

Additive manufacturing techniques can design and fabricate lightweight structures with complex geometries such as lattice structures.

会议

additive manufacturinglattice structuredynamic response

结构动力响应灵敏度求解的径向基函数方法

应用已经提出的径向基函数逼近方法求解结构动力响应，在此基础上提出了一种新的结构动力响应灵敏度计算方法，包括动力位移、速度、加速度和急动度(加速度对时间的导数)的灵敏度，并给出了灵敏度初值的确定方法。通过设计算例，与基于精细积分法和差分法的灵敏度计算结果进行比较，验证了本文方法的可靠性。

会议

径向基函数动力响应灵敏度动力有限元

Wrinkle-free design of thin membrane structures

Thin membrane structures would experience wrinkling due to local buckling deformation when compressive stresses are induced in some regions.Using the stress criterion for membranes in wrinkled and tau

会议

Thin membraneWrinkletopology optimizationPrincipal stress criterion

Applications of Symmetry and Pattern Repetition for Periodic Structures Using Parameterized Level Se

其他学术论文