运用J函数建立含水饱和度模型--以西江24-3油田为例

来源 :第四届全国特种油气藏技术研讨会 | 被引量 : 0次 | 上传用户：aixiaowen

【摘要】

：

运用压汞实验数据建立毛管压力与含水饱和度的关系,根据多块岩样压汞曲线用指数函数拟合J函数与含水饱和度关系;应用自由水界面原理结合petrel软件建立自由水界面模型.运用克里金插值方法,结合西江24-3油田储层物性分析,通过水平井变差函数分析,在J函数的约束下用建立含水饱和度模型,充分体现地质、数学、计算机技术、油藏物理等理论综合建立储层模型的优势.

【作者】

：

印森林陈恭洋周锦解传军胡勇

【机构】

：

中石化胜利油田分公司,山东德州251507 长江大学,湖北荆州434023

【出处】

：

第四届全国特种油气藏技术研讨会

【发表日期】

：

2010年10期

【关键词】

：

油田开采含水饱和度模型 J函数自由水界面克里金插值法

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

其他文献

Research and development on high performance anchor cable dynamometric system based on vibrating-wir

Outstanding anchor cable dynamometric system is urgently needed in anchor engineering of pre-stressed anchor cable so as to control tension during the process of anchor cable construction and monitor

会议

Vibrating-wire sensor technologyanchor cable dynamometric systemmathematical m

稠油潜山裂缝油藏封堵底水技术研究与应用

曙一区稠油古潜山属底水块状油藏,储层裂缝发育,开发中存在含水上升速度快、区块年产油量下降速度快等问题.通过室内实验配方不断改进及施工工艺的优化、创新和完善,形成了颗粒凝胶型、水玻璃黏土胶及高强度树脂复合段塞相结合的系列堵水方式.根据各自特点确定选井条件,结合油井的具体情况采取相应配套堵水方式,提高了措施的针对性和成功率,有效地抑制了底水的锥进速度,改善了开发效果.2008～2009年期间,在研究区

会议

稠油潜山油藏封堵边底水技术复合段塞堵剂裂缝性分析

地球物理技术在西部凹陷西斜坡薄层稠油评价开发中的应用

针对西部凹陷西斜坡兴隆台油层含油分布范围广、厚度变化大、动用程度不均衡的现状,通过加强三维地震、储层反演等地球物理技术在该区兴隆台薄层稠油评价开发工作中的研究与应用,有效地指导了该区兴隆台薄油层的评价与开发工作,对其他类似地区薄层稠油的评价与开发工作具有借鉴作用.

会议

薄层稠油开发储层评价地球物理技术西部凹陷西斜坡

SOM-based Quality Assessment for Resistance Spot Welding with Featured Electrode Displacement Signal

To classify the quality of the resistance spot welding process, the relationship between the welder electrode displacement curve characteristics and the weld shear force has been explored where 11 sta

会议

Resistance spot weldingSOMquality assessmentelectrode displacement

Preparation and performance studies on high noise reduced composites based on BaSO4 filled Poly(viny

As a widely used general polymer material, PVC shows the great potential value for insulating or damping the sound and vibration due to their unique combination of structure, inherent damping, light-w

会议

PVCBaSO4sound insulationsound transmission loss

Effects of plasma spraying powers on microstructure and property of nanostructured composite coating

In-situ nanostructured FeAl2O4 composite coatings were prepared by plasma spraying Al/Fe2O3 composite powders using different spraying powers.The effects of plasma spraying powers on microstructure an

会议

Reactive plasma sprayingceramic matrix compositenanostructured coatingsmicros

Influence of Electron-Beam Superposition Welding on the IMC-layer of a Cu/Ti Join

QCr0.8 was electron-beam welded to TC4 and the effect of the intermetallic layer (IMC-layer) on the mechanical properties of the joint was investigated.IMC-layers are joint weaknesses at the Cu fusion

会议

Cu/Tielectron beam superposition weldingIMC-layerweld sequence

Effects of isothermal process parameters on the microstructure of Mg-8%Al-1% Si alloy by semisolid i

A semisolid microstructure of Mg-8%Al-l%Si alloy was fabricated by isothermal heat treatment process.The effects of isothermal process parameters such as holding temperature and holding time on the mi

会议

Semisolidisothermal heat treatmentMg2Si phasemorphology

Novel multilayer Mg-Al intermetallic coating for corrosion protection of magnesium alloy

A novel multilayer Mg-Al intermetallic coating on magnesium alloy was successfully obtained by AlCl3-NaCl molten salt bath treatment.Molten salt bath treatment at 400℃, which is lower than the treatme

会议

multilayer structurediffusionintermetallic coatingcorrosion

Thickness distribution and mechanical property of sheet metal incremental forming based on numerical

Sheet incremental forming (ISF) is known for short lead time and requiring no dedicated dies.Thickness thinning, however, has always been a puzzle which hinds the wide application of ISF.And little wo

会议

Incremental formingFEMthickness distributionmechanical property

运用J函数建立含水饱和度模型--以西江24-3油田为例

其他学术论文