连铸方坯内拉坯方向碳元素分布时间序列的典型分析

来源 :第九届中国钢铁年会 | 被引量 : 0次 | 上传用户:sunapplesun
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
本文先利用原位分析技术中的线扫描得到连铸方坯内部在中心线位置、V形负偏析带以及CET区域这三个位置沿拉坯方向的碳元素分布.由于碳元素沿拉坯方向的分布是随着时间而不断形成的,因此可将其处理为三组时间序列.在此基础上,利用乘积季节模型等经典时间序列分析技术对这三组时间序列进行了分析,并得出中心线位置处所对应的时间序列具有一定的周期性特征.同时还发现在沿拉坯方向的同一个位置点,中心线位置处碳元素含量与CET位置碳元素含量的相关性要比中心线位置处碳元素含量与V形偏析带碳元素含量的相关性更为明显.这很有可能是由于连铸方坯内不同区域具有不同的凝固特点而导致的.
其他文献
通过控制轧制和控制冷却工艺试验,研究了终轧温度和终冷温度对Q690CFE组织和性能的影响.结果表明,终轧温度和终冷温度主要是通过改变试验钢的组织组成和晶粒大小来对其力学性能产生影响,在780~820℃终轧温度范围内,终轧温度对试验钢组织性能影响较小;在530~650℃终冷温度范围内,随着终冷温度的升高,粒状贝氏体组织中逐渐出现不规则分布的MA岛组织,且MA岛由细小弥散球形颗粒状向粗大尖角状转化,屈
本文对西宁特钢EAF-LF-VD-CC生产的低氧GCr15棒材中夹杂物进行了研究。研究发现,横截面与纵截面夹杂物均主要以氧化物、硫化物、氮化物以及两者之间的复合态形式存在;从边缘到中心,横截面夹杂物数量分别为307个/mm2、129个/mm2、210个/mm2,纵截面夹杂物数量分别为65个/mm2、32个/mm2、97个/mm2,夹杂物的数量均呈现出先减后增的趋势,这与钢液凝固时温度差所导致的钢液
基于邢钢轴承钢生产流程,通过提高转炉出钢碳含量和控制转炉下渣量,增加转炉和LF 脱氧力度,延长RH 真空处理时间和软吹时间,改善保护浇铸等工艺使轴承钢全氧含量显著降低,由原来的平均7.61×10-6 降低至5.93×10-6,且全氧含量≤6.5×10-6 的比例由原来的30.4%提高至79.8%.
H2 injection through the shaft into blast furnace (BF) is a key technology for further reduction of CO2 emission from BF.It is well known that H2 accelerates reduction of burdens,but not well known of
In 2010 Paul Wurth introduced the G3 gearbox,surpassing in any aspect the reinforced water cooled gearbox which was developed end of the 1980s.The G3 gearbox relies,amongst other features,on a pressur
The paper deals with new market developments in the area of advanced high-strength steels (AHSS) like dual-phase,martensitic,complex-phase,TRIP and furthermore highest strength pipe grades.When attemp
The paper gives an insight on important questions for building cold mill complexes and is explaining different references from Europe and Asia - from small capacities up to high end automotive facilit
Macrosegregation and centre porosity are two of the major quality issues in the continuous casting of medium and large round blooms.Mould,strand and final stirrer are some of the most used tools to im
In China as well as everywhere in the world,operators of cold rolling mills are interested in increased yields,better product quality and economic operation of the facility.Therefore they continuously