【摘 要】
：
The implementation of EVP is becoming more and more important with the development of new energy vehicles and the target of low energy consumption. It has a great influence on NVH, pedal feeling and b
【机 构】
：
Dong Feng Motor Corporation Technical Center
【出 处】
：
第19届亚太汽车工程年会暨2017中国汽车工程学会年会
论文部分内容阅读
The implementation of EVP is becoming more and more important with the development of new energy vehicles and the target of low energy consumption. It has a great influence on NVH, pedal feeling and braking. The process of vehicle matching is still un- der development due to lack of application experience. Based on previous development experience, this paper puts forward a vehicle matching process that can be used to save time and cost and ensure driving safety. How to carry on the vehicle matching is the focus of the study in consideration of that EVP is a mature product, especially how to design control based on vehicle state are not clearly described in published articles. This paper focused on control and fault detection strategy of EVP. EVP structure, an application method of comparison, key bench tests related to performance of EVP, vehicle tests re- sults are illustrated. Vehicle loading methods combined with layout and system architecture is also discussed.
其他文献
According to the theory of simulation-screw-car, we concluded a debugging method. Recognize the affection of welding process and plying-up of parts. Rapidly apply the counter measure, reduce the cost
The article is about how to improve the automobile paintwork sensible quality. Through the methods of advanced material application and coating process improvement, to improve the optical characterist
In this work we present a failure investigation on turbine housing used in automotive diesel turbocharged engine which had run about 50, 300 km, while the expected life was 100, 000 km. The turbine ho
The ele ctromagnetic(EM)noise induced by alternator affects the subjective evaluation of the NVH performance inside the vehicle significantly. The EM noise inside the vehicle is mainly transmitted by
This paper describes a method to design contact pattern of spiral bevel gear in drive axle. Gear mounting position changes under load and so does the contact pattern. Finite element analysis software
An improved Articulation Index(AI)algorithm was presented for the first time to solve the defect of insufficient differ- ence discrimination of the traditional AI algorithms to the automotive acoustic
本文对汽车加速行驶车外噪声的室内,外通过噪声测量存在的差异性问题进行了研究,通过应用静音光头轮胎及其附加声学装置最小化室内轮胎噪声,从而获取室内情况下的动力总成和进排气噪声,自由滚动轮胎噪声和轮胎牵引扭矩噪声均可在室外获取,实现了室内通过噪声结果的计算合成与室外通过噪声测试结果的量化比较,很好地对标精度证实了方法的有效性.
In modern automotive industry, engine vibration isolation has been an emergent issue with the increasing requirement of ride comfort and fuel efficiency performance. Semi-active hydraulic engine mount
针对汽车减振器下连接橡胶轴承,建立Voigt-Kelvin、Maxwell、Zener和Generalised-2四种不同粘弹性模型,并将其与摩擦力模型并联,在MATLAB/Simulink中进行仿真.将仿真结果与实际实验数据进行对比,发现Generalised-2模型与实际情况最符合,Kelvin-Voigt模型与实际情况最不符合.将Generalised-2模型与Voigt-Kelvin模型分
针对车辆怠速时驾驶座椅振动现象,对发动机悬置上下端及座椅导轨的振动加速度信号做阶次跟踪和频谱分析,认为该振动主要由发动机自身二阶激励引起.为消除该现象,将动刚度二级可变的空气弹簧式半主动控制液压悬置应用于发动机左侧支撑.试验对比表明,半主动控制的发动机悬置对怠速时发动机左侧的异常振动具有很好的隔离效果,提升了车辆怠速工况的振动舒适性,同时也满足了车辆正常行驶时的悬置动刚度要求.