【摘 要】
：
Advanced high strength steel(AHSS)iswidely used in the automotive industry because of its advantages for weight reduction and for the resulting improvement in crashworthiness and safety.However it is
【机 构】
：
School of Mechanical and Mining Engineering,University of Queensland,St Lucia,QLD 4072,Australia
【出 处】
：
第十届中国钢铁年会暨第六届宝钢学术年会
论文部分内容阅读
Advanced high strength steel(AHSS)iswidely used in the automotive industry because of its advantages for weight reduction and for the resulting improvement in crashworthiness and safety.However it is still a challenge to fabricate AHSS products at room temperature due to its high strength and limited elongation.This greatly limits the new materials application and the spread of its use.Chain-die forming has been proposed and developed as an extension to roll forming in fabricating AHSS products.It has shown its superiority by reducing redundant plastic strains during forming and nearly zero residual stresses can be achieved through increasing the length of deformation zone,via increasing the apparent roll radius.In this paper,an experimental investigation is aiming to demonstrate the working principle and investigate the characteristics of Chain-die forming AHSS products with various material properties and geometrical dimensions which can further expand the application of Chain-die forming and accelerate its commercialization,particularly in automotive industry.As the longitudinal strain,residual strain and springback are regarded as the crucial factors in the quality evaluation of AHSS products,the relationships and comparisons of these factorsof Chain-die formed AHSS products with various material properties and geometrical dimensions are presented.Finally,some concluding remarks for further study are made from the experimental investigation.
其他文献
利用RTW-10熔体综合物性测定仪,采用内柱体旋转法测量Cr2O3含量对CaO-SiO2-MgO-Al2O3-Cr2O3渣系的黏度及熔化性温度的影响,并利用FactSage热力学计算软件分析CaO-SiO2-MgO-Al2O3-Cr2O3渣系的相图。实验结果表明,固定高炉渣碱度为1.11时,随着炉渣中Cr2O3含量的增加,炉渣黏度下降,炉渣熔化性温度升高。当Cr2O3含量为1％～3％时,炉渣熔化性
Coal combustion is divided into two stages.One is the emission and combustion of volatiles and the second is the combustion of coal char.In this paper,effects of CaO on structure evolution and combust
Lean duplex stainless steel,in which nickel is replaced by manganese and nitrogen,is one of the most important trends for developing high strength stainless steels.However,manufacturing thin gage stri
超(超)临界机组不断提高的蒸汽参数,使对耐热钢的性能要求也在不断提高,本课题在探索研宄适合更高蒸汽参数的超(超)临界机组用铁素体耐热钢为背景下展开研究.本文以一种含Co、B分别为1.0％和0.022％的新型铁素体耐热钢为研究对象,通过对比讨论不同正火温度和冷却方式对微观组织和室温力学性能的影响规律,提出优化正火温度和冷却方式.结果发现:随正火温度升高,奥氏体化充分,板条状回火马氏体组织粗化,原奥氏
Type-429 Ferritic stainless steel is an low cost material to be used in hot end of automotive exhaust system,this grade was widely used for the fabrication of manifold,which usually work at 800℃-900℃.
Pulverized coal injection(PCI)iswidely practised in ironmaking industry due to many benefits in particular the reduction of production cost,where black coal was largely used at present.Victorian brown
通常认为增加精轧应变可以有效细化管线钢组织,从而提高管线钢的强度和韧性,然而,随着产品厚度的增加,该调整方法受设备的限制,成为生产技术瓶颈.本研究采用Gleeble-2000热模拟试验机、金相分析、扫描电镜技术等系统研究了轧制工艺对管线钢组织和性能的影响.研究结果表明:厚规格产品韧性不符合标准归因于边部和心部冷却梯度增加,边部以粒状贝氏体组织为主,而心部存在多边形铁素体,这种组织梯度最终引起韧性的
将膜法制氧、富氧助燃工艺设备在武钢多座活性石灰回转窑进行了应用,本文介绍了其工艺流程及主要设备,并在实际工况下综合评测了其使用效果,该工艺经适当改造可适用于回转窑等动态窑炉.采用该工艺有效提高了回转窑的燃烧效率及各项运行指标,显著降低了产品的煤耗及温室气体排放.
针对宝钢X65级UOE管线钢管,应用纤维素焊条进行高速环缝打底焊接和热焊,填充盖面焊接选用低氢焊条,并对环焊接头进行冲击韧性和CTOD断裂韧性分析。同时,将纤维素焊条高速环焊接头与全部低氢焊条环焊接头在冲击韧性和断裂韧性方面进行比较,结果表明;无论是焊态还是消氢处理态,针对X65这种较低强度钢管,纤维素焊条高速环焊接头均具有良好的冲击韧性和断裂韧性。纤维素焊条高速环缝焊接在高强度管线钢管中的应用有
通条性能不稳定、组织不均匀是80MnCr盘条在拉拔或扭转加工过程中发生断裂的主要原因之一,本文利用淬火膨胀仪绘制了80MnCr盘条的静态CCT曲线,采用切线法得到了相变过程中的临界转变温度点,通过金相显微镜观察了不同冷却速度条件下80MnCr盘条的析出组织,通过扫描电镜分析了不同冷却速度条件下80MnCr盘条的珠光体片层间距,研究了不同冷却参数对80MnCr盘条相变组织转变的影响。结果表明,80M