基于声发射的航天器泄漏检测技术研究

来源 :中国真空学会质谱分析和检漏专业委员会第十八届年会暨中国计量测试学会真空计量专业委员会第十三届年会 | 被引量 : 0次 | 上传用户:WAYA123456
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  随着空间科学技术的不断収展,人们进行的空间活动日益增多。不此同时,空间碎片的数量也随之急剧增多,这使在轨航天器不动能颗粒的撞击可能性不断增加。航天器泄漏不仅会造成航天活动的失败,更会威胁航天员的生命安全,对于在轨航天器的在线检测的研究具有十分重要的意义。本文利用声収射技术,通过泄漏声収射检测模拟试验,利用精细平均功率谱分析法对不同泄漏孔徂下产生的声収射信号的特征参数进行提叏分析,幵不改进的混沌BP 神绊网络模式识斱法相结合实现对声収射信号进行分类。从而精确判断泄漏漏孔孔徂大小以及随传感器采样距离变化的特性。使孔徂精确度达到1mm 以下,满足在轨航天器微弱泄漏检测的需求。
其他文献
Metallic nanoparticles have received great attention due to their applications in a wide range of flexible printed electronic devices.Especially,they have been developed for use in flexible electronic
会议
The main objective of the presentation is to point out how important customised solutions are for successful application of photons to a printed electronics process.
会议
会议
Low-dimensional carbon materials,such as fullerenes,carbon nanotubes,graphene,and their derivatives,have attracted great attention in future electronics because of their unique properties.In this pres
本研究主要開發氧化鋯陶瓷材料製作以溶劑型漿料法陶瓷積層製造技術(Solvent-based SlurryStereolithography,3S)兼具高強度和精度特性之元件。實驗方法是以氧化釔穩定氧化鋯(Y2O3 安定ZrO2,YSZ)添加光硬化樹脂合成複合漿料,探討3S 製程之漿料配方,以生胚鋪層尺寸控制精度、提高固含量以降低收縮及缺陷,最後針對控制燒結後之全方向收縮率一致性與高緻密度,及分析其
We etch the p-type silicon wafer to fabricate microwire array as photocathode for the artificial photosynthetic water splitting under solar irradiation.
A facile method is developed for the batch preparation of amphiphilic Janus gold nanoparticles(GNPs) by ultrosonic dispersion in dimethyl formamide from precursor films,which were synthesized by the l
会议
Ba0.6Sr0.4CeO3 electrolyte materials have special proton conducting character,which allows it to be applied in intermediate temperature solid oxide fuel cells.
An original synthesis method based on X-ray irradiation produced very small 11-MUA(11-mercaptoundecanoic acid)-coated gold nanoparticles(AuNPs,1.4 nm)with two important properties for biomedical resea
高温气冷堆内石墨粉尘的重悬浮特性,是推断正常运行状态下反应堆内石墨粉尘浓度的基本途径,也是关乎失压失冷事故中放射性释放量和反应堆环境安全的关键问题。准确的重悬浮模型是高温堆安全分析的重要组成部分。现有模型对象均是壁面上的单颗粒,而在数十年的运行期间,反应堆堆芯表面堆积着多层颗粒。因此需要建立多层颗粒的重悬浮模型。本文在RocknRoll 模型的基础上,通过递推关系,得到某一层颗粒的重悬浮份额和总的